10 Best Bike Chain Cleaner

It possible to clean your chain in under 60 seconds, without removing it from the frame with three spinning brushes side plates covers a metal, wear, magnet and no drip angle. A clean chain is only a minute away to use the pro chain cleaner start by filling the unit with citrus or multi degreaser to the fill line to clean, put the bottom of the unit under the chain and depress the chain, with the top secure with the wire strap closure with the chain near the rear.

Derailleur back pedal slowly for approximately 20 revolutions to fully clean the chain. When clean under the wire strap closure to remove the unit, use a moist rag to remove any residue left by the degreaser, then you can reload your chain and go for a ride.

Finish line one step cleaner and why would I want to use one step? Well, one step is a great product. If you just want to lube your chain and go ride, you want it simple, you want it easy. This is the product, because when you apply it, it has a very aggressive penetrant that gets in and pushes all the old bloom and the accumulated dirt grit grime out of the park, shaving your whatever moving and leaves behind fresh nice loop, you’re ready to go so so a good way to think about.

It is a lot of times, we’ll wonder! Well how often do I relive a window every way you know what should I be looking for? Well with one step, all you’re really looking for is when the chain gets dirty or drawing that’s it. You just want to apply some more if you want to worry about cleaning the chain just spray on some one-step, it’ll penetrate in there and push all the other junk out, leave behind nice, fresh lubricant, and you go right so that easy wet once that is a wet style lubricant.

So it stays wet on the chain and in some drier, dustier climates. You may find that it Dirty’s up fairly, often and so you’re applying. And if you find yourself that you find that you’re applying blue more than you like then try our dry Teflon lube. It attracts less dirt because it goes on the chain wet but dries. But you’ll notice with the dry Teflon movement does not have a built-in cleaning function like the one-step, so eventually that chain or part will accumulate enough dirt.

They don’t need to be cleaning. You’ll need to use. One of our degree search see our degreasers in the videos on those four good explanations there. But if you want a one-step, 1 product solution to keeping your parts running smooth and clean, then this is a very popular. The folks who just want it easy and want to get back on their bike and go ride.

Wd-40 bike degreaser is great for the from bicycle. Doraleous first place the bike on a stand with a rag under the derailleur to collect any dirty or excess liquid apply by spraying liberally onto the derailleur and Terranea jockey wheels to remove heavy or stubborn build-up as dirt. You may need to agitate with a rush allow the formula to remain in contact for a few minutes.

The liquid starts to soften and solubilized dirt, grease and oil to lift it from the derailleur easily to finish spray with clean water from a hose finally dry with a clean cloth or towel cleaning. Your derailleur regularly prolongs the performance of your drivetrain by reducing, wear and tear caused by the grinding of dirt particles.

The majority of people who own a bike understand the importance of proper chain maintenance and that a clean, well lubricated chain makes your bike happy and thus providing a better riding experience. However, there are those of us who are reluctant to spend an eternity cleaning our change with an assortment of brushes and ending up with the chain that is still gummy, I’m, exaggerating of course, but manufacturers are the need for a product that can swiftly clean your chain.

Introducing the Park Tool cyclone I got this product off Chain Reaction Cycles for about $25 Canadian I had always wanted one, so I decided to take the plunge. Hon not intended. The tool was a lot more compact than what I imagined and seems to be made of very solid material. Perfect for those who like to drop expensive items inside the cyclone, are a variety of scrubbing brushes for getting in every nook and cranny of your chain in a small magnet each for gathering up metal shavings, the product is fairly lightweight for all you lately needs and, as I mentioned is quite small.

The instructions are lacking, but hey I’ll figure it out. If not Google the that’s onto your chain, and you can begin using the tool, I was using a citrus degree to that been diluted with bottled water, no reason for the bottled water. It’s just what I had on hand I find it rather enjoyable using the cycle I’m a bit of a frequent that come to the Colinas and function of my chain and the tool feels like it’s doing a great job. The action is very stout and feels satisfying in your hands.

Moving on I spend about a minute with the cyclone and left it to sit for a few before devs on my bike with a car, because now there is not a promised maximum amount of time. You’re supposed to spend using the cyclone to achieve mad fun. Leanness geez, I can’t believe I got that one one take I chose a minute which would be an absurdly short amount of time if I had been using just brushes. I can honestly say that I was impressed with the cyclone, even though my chain was not perfect.

It shaved me a good chunk of time that it can be used for riding I’m, making more content for you guys. There were a few spots that had grease left over but, like I, said, I only spent a whole 60 seconds cleaning the chain, so I didn’t use a cyclone once and then solidify my opinion. Over the course of a month, I used a tool and I can say that I was extremely happy with my purchase. Shifting improved and my bike was a lot quieter. I was able to get my chain perfect after using the cyclone for about three minutes.

This is well worth the money and I would highly recommend you get one for your toolbox. The park tool cyclone chain cleaner, is one of the most user-friendly convenient tools. I have ever use and spare parts are available. If you love using it as much as I get it guys.

Chain, cleaner, it’s being filled up with cleaner or we can do it fill it up. You know just click it on then start back I. Do this process repeat this process about three to four times by that time the chain is pretty clean, I run a couple of flushes of water three and then pretty much dry, the chain off, and it’s pretty straight forward. Job exhibit. When you do what I did then and the young you can see from here, just the state of the water and it’s it’s clearly removing all the grease and also and the oil and depth from the channel.

These are the park tool bike chain model, but it broke. I thought this is a replacement, but I, don’t think that’s gonna work either. So let me take you through why this one broke and the things that I think will keep this from being a good replacement. This is the Park Tool cm five-point cheer. You can see it just there. It’s the consumer model. I use this once a week, sometimes more, but at least once a week and here’s how it works. It’s got a top that comes off like this there’s a brush up there that spins freely.

This is the same brush right here, and this is a slightly different brush. You bring a chain through here and then you put the top one like this and the bottom secures to the top. With this latch. You flip it around like that and that’s where the first problem comes in. You can see there are a network of spider cracks if we get the glare off there, bunch of spider cracks down here and that’s because this process puts a lot of stress right there. This is not the original screw. There was a pin in there that was like riveted in some way that fell out a long time ago, and you can see that the other the other latch is here, because that one has also just broken, and this one actually I think has yeah.

It has worse spider cracks, so you can see the problem there, and this is just due to choosing a plastic. That’s not strong enough for the dimensions of these features. There’s a lot of force going in there and not enough plastic, and so it cracks and it’s a it’s a brittle plastic. So that’s a problem. The brittleness of the plastic also leads to a second problem which is I dropped us the other day and it cracked everywhere. There’s a big crack here. There’s a big crack here. It goes all the way down.

There’s a magnet, that’s supposed to go there, but that part broke also I, don’t know it just seems like this plastic is too brittle for this application, but as you’ll see when we compare it to this other one, it does have some strong points. So, let’s come back to that. This is the professional model. This one is the CM 25 professional chain cleaner. It has a housing made from aluminum, it’s a cast, aluminum looks like a die cast and maybe powder coated blue. Let me show you a couple things you can’t see on the website.

The first one is the way the handle attaches. The handle attaches right here with a little set screw. One one set screw, let’s point with something a little smaller there’s this set screw right there and the problem with that set it down. So you can see is that the handle Wiggles it pivots about that set screw. The set screw does a great job of holding on to the the main case, but there’s a bunch of slack bunch of slop at the edges here, and it allows this to rotate, and this is I just just got this and unpack this, and that is not gonna get any better with time.

Let me take this off and I’ll show you why that is so. I’ve loosened up the set screw, so the handle can can move now, and you can see the problem and the amount of lateral slop that it’s got if this were tight and the set screw was just holding it in then that would be just a fine design, but it’s not the set screw has to hold it in, but also try to restrain this this other slop and because there’s only one, it’s not able to do it. If there were two it would you okay, but there’s only one. One way to tackle this kind of design problem is to use instead of a square.

If we look at this piece of the handle here, you can see that it’s square. This is at a 90 degree angle with that, and there are some small champers here, but the the inside surface of this of the case I’ll show you what I mean right right in here. That does not have a corresponding chamfer, and so that means that this, when you put this in here, it doesn’t wedge itself in there, it just rattles around and that’s actually where this one works pretty well. This handle is it’s not a square? It’s a it’s a triangle.

The top is slightly narrower than the bottom, so that when you slide it in here that wedges itself in place and holds it firmly, despite a lack of any fasteners at all that that has worked great, and so if this one were improved with some kind of taper. That would that would handle this problem and allow one set screw to hold it in place. Once we open it up once we open it up, the the consumer model uses individual brushes, but this one doesn’t tip over, but this one the brushes come out as a cartridge, and so there’s the second problem.

This sponge falls right out and this cloth the chain the chain moves through this way, and so it gets scrubbed and then presumably, this sponge and cloth dry. It dry it out before it goes outside, but the sponge doesn’t stay in there. So it’s gonna, you know, fall out and be lost immediately and the reason it doesn’t stay in there is that it’s it’s too short. If it were, if it were a little bit longer, then it would stay in there. The sponge is held between this cross bar and that cross bar, and you can see daylight on both sides, so it just rattles around in there and there’s nothing to hold it.

Sometimes you get lucky in it and it stays in for a minute. It’ll just fall right out. The same is true on the bottom, but you’ve got gravity helping you out. In that case, this this cloth is really a pain that comes that comes out quickly too. This design is a little weird, it doesn’t look like I, don’t know the top and the bottom cloth retaining features are designed separately like they’re, not the same, and that’s a little weird, because the bottom cloth pertaining features actually work pretty good, because you can see the cloth pokes through goodway’s, and so it’s got good.

It’s got a good hold on there and the reason it can do that is that the cloth features on the bottom are closer together. They are on the top, let’s zoom in so you can see what we’re talking about. So we put these side by side. You can see that so this one is the bottom. It’s got the big brush. You can see that they’re closer together. If we line up the left-hand cloth slot, then you can see the right hand slots don’t line up and I’m surprised by that it would have expected them to use the same.

You know the same features on top and bottom yeah. Part of the reason why they didn’t is that this one’s getting pretty close to the end, so you have to kind of incorporate it into this. This end feature: ok, fair enough, but they you know the the top handles that problem differently and seems like the bottom could have as well. It would be more effective to do that, and the second kind of weird thing is that the width of the slots are different, so notice that the left hand cloth slots. The top slot is wider than the bottom slot.

The bottom the bottom slots match each other and the bottom slots match the top right slot. The top left slot doesn’t match, so the cloth just falls right out. That’s that’s pretty weird um yeah, so I don’t know in. In my view, that means that those those drying features aren’t aren’t very useful. Maybe maybe this sponge will stay in, but there’s there’s all this other stuff, that’s gonna. Either these will get worn out right away or more likely, they’ll fall out and this one will fall out and get lost too.

So that means that about I don’t know half the width is is not very useful and the handle Wiggles so I I’m not sold on this um on this pro version, I think that the case will hold up just fine, but I think the guts are not are not very useful and this consumer version is made out of a plastic. That’s that’s too. Brittle they’ve changed the design recently. This is the 5 2 and they have now the 5 3 available. But the plastic is the same. It’s gonna have the same cracking issues, at least at least from dropping, if not from the end latches, which, which they’ve also changed so I’m I’m feeling like Park, doesn’t make a tool, that’s built for me, a guy that you know I’m just a regular guy, but I use it pretty frequently once a week, sometimes more and I’d love to buy something from them.

But I don’t think either of these is the right tool.

These are the park tool bike chain model, but it broke. I thought this is a replacement, but I, don’t think that’s gonna work either. So let me take you through why this one broke and the things that I think will keep this from being a good replacement. This is the Park Tool cm five-point cheer. You can see it just there. It’s the consumer model. I use this once a week, sometimes more, but at least once a week and here’s how it works.

It’s got a top that comes off like this there’s a brush up there that spins freely. This is the same brush right here, and this is a slightly different brush. You bring a chain through here and then you put the top one like this and the bottom secures to the top. With this latch. You flip it around like that and that’s where the first problem comes in. You can see there are a network of spider cracks if we get the glare off there, bunch of spider cracks down here and that’s because this process puts a lot of stress right there.

This is not the original screw. There was a pin in there that was like riveted in some way that fell out a long time ago, and you can see that the other the other latch is here, because that one has also just broken, and this one actually I think has yeah. It has worse spider cracks, so you can see the problem there, and this is just due to choosing a plastic. That’s not strong enough for the dimensions of these features.

There’s a lot of force going in there and not enough plastic, and so it cracks and it’s a it’s a brittle plastic. So that’s a problem. The brittleness of the plastic also leads to a second problem which is I dropped us the other day and it cracked everywhere. There’s a big crack here. There’s a big crack here. It goes all the way down. There’s a magnet, that’s supposed to go there, but that part broke also I, don’t know it just seems like this plastic is too brittle for this application, but as you’ll see when we compare it to this other one, it does have some strong points.

So, let’s come back to that. This is the professional model. This one is the CM 25 professional chain cleaner. It has a housing made from aluminum, it’s a cast, aluminum looks like a die cast and maybe powder coated blue. Let me show you a couple things you can’t see on the website. The first one is the way the handle attaches. The handle attaches right here with a little set screw. One one set screw, let’s point with something a little smaller there’s this set screw right there and the problem with that set it down.

So you can see is that the handle Wiggles it pivots about that set screw. The set screw does a great job of holding on to the the main case, but there’s a bunch of slack bunch of slop at the edges here, and it allows this to rotate, and this is I just just got this and unpack this, and that is not gonna get any better with time. Let me take this off and I’ll show you why that is so. I’ve loosened up the set screw, so the handle can can move now, and you can see the problem and the amount of lateral slop that it’s got if this were tight and the set screw was just holding it in then that would be just a fine design, but it’s not the set screw has to hold it in, but also try to restrain this this other slop and because there’s only one, it’s not able to do it.

If there were two it would you okay, but there’s only one. One way to tackle this kind of design problem is to use instead of a square. If we look at this piece of the handle here, you can see that it’s square. This is at a 90 degree angle with that, and there are some small champers here, but the the inside surface of this of the case I’ll show you what I mean right right in here. That does not have a corresponding chamfer, and so that means that this, when you put this in here, it doesn’t wedge itself in there, it just rattles around and that’s actually where this one works pretty well.

This handle is it’s not a square? It’s a it’s a triangle. The top is slightly narrower than the bottom, so that when you slide it in here that wedges itself in place and holds it firmly, despite a lack of any fasteners at all that that has worked great, and so if this one were improved with some kind of taper. That would that would handle this problem and allow one set screw to hold it in place. Once we open it up once we open it up, the the consumer model uses individual brushes, but this one doesn’t tip over, but this one the brushes come out as a cartridge, and so there’s the second problem.

This sponge falls right out and this cloth the chain the chain moves through this way, and so it gets scrubbed and then presumably, this sponge and cloth dry. It dry it out before it goes outside, but the sponge doesn’t stay in there. So it’s gonna, you know, fall out and be lost immediately and the reason it doesn’t stay in there is that it’s it’s too short. If it were, if it were a little bit longer, then it would stay in there.

The sponge is held between this cross bar and that cross bar, and you can see daylight on both sides, so it just rattles around in there and there’s nothing to hold it. Sometimes you get lucky in it and it stays in for a minute. It’ll just fall right out. The same is true on the bottom, but you’ve got gravity helping you out. In that case, this this cloth is really a pain that comes that comes out quickly too. This design is a little weird, it doesn’t look like I, don’t know the top and the bottom cloth retaining features are designed separately like they’re, not the same, and that’s a little weird, because the bottom cloth pertaining features actually work pretty good, because you can see the cloth pokes through goodway’s, and so it’s got good.

It’s got a good hold on there and the reason it can do that is that the cloth features on the bottom are closer together. They are on the top, let’s zoom in so you can see what we’re talking about. So we put these side by side. You can see that so this one is the bottom. It’s got the big brush. You can see that they’re closer together. If we line up the left-hand cloth slot, then you can see the right hand slots don’t line up and I’m surprised by that it would have expected them to use the same.

You know the same features on top and bottom yeah. Part of the reason why they didn’t is that this one’s getting pretty close to the end, so you have to kind of incorporate it into this. This end feature: ok, fair enough, but they you know the the top handles that problem differently and seems like the bottom could have as well. It would be more effective to do that, and the second kind of weird thing is that the width of the slots are different, so notice that the left hand cloth slots.

The top slot is wider than the bottom slot. The bottom the bottom slots match each other and the bottom slots match the top right slot. The top left slot doesn’t match, so the cloth just falls right out. That’s that’s pretty weird um yeah, so I don’t know in. In my view, that means that those those drying features aren’t aren’t very useful. Maybe maybe this sponge will stay in, but there’s there’s all this other stuff, that’s gonna.

Either these will get worn out right away or more likely, they’ll fall out and this one will fall out and get lost too. So that means that about I don’t know half the width is is not very useful and the handle Wiggles so I I’m not sold on this um on this pro version, I think that the case will hold up just fine, but I think the guts are not are not very useful and this consumer version is made out of a plastic. That’s that’s too.

Brittle they’ve changed the design recently. This is the 5 2 and they have now the 5 3 available. But the plastic is the same. It’s gonna have the same cracking issues, at least at least from dropping, if not from the end latches, which, which they’ve also changed so I’m I’m feeling like Park, doesn’t make a tool, that’s built for me, a guy that you know I’m just a regular guy, but I use it pretty frequently once a week, sometimes more and I’d love to buy something from them.

But I don’t think either of these is the right tool.

The finish-line pro chain cleaner, makes it possible to clean your chain in under 60 seconds, without removing it from the frame with three spinning brushes side plates covers a metal, wear, magnet and no drip angle. A clean chain is only a minute away to use the pro chain cleaner start by filling the unit with citrus or multi-degree search. The fill line to clean, put the bottom of the unit under the chain and depress the chain, with the top secure with the wire strap closure with the chain near the rear.

Derailleur back pedal slowly for approximately 20 revolutions to fully clean the chain. When clean under the wire strap closure to remove the unit, use a moist rag to remove any residue left by the degreaser, then you can remove your chain and go for a ride.

It possible to clean your chain in under 60 seconds, without removing it from the frame with three spinning brushes side plates covers a metal, wear, magnet and no drip angle. A clean chain is only a minute away to use the pro chain cleaner start by filling the unit with citrus or multi degreaser to the fill line to clean, put the bottom of the unit under the chain and depress the chain, with the top secure with the wire strap closure with the chain near the rear.

Derailleur back pedal slowly for approximately 20 revolutions to fully clean the chain. When clean under the wire strap closure to remove the unit, use a moist rag to remove any residue left by the degreaser, then you can reload your chain and go for a ride.

Wd-40 bike degreaser is great for the removal of thick dirt. Grease and grime from your bike chain. First place the bike on a stand so that the rear wheel is free to turn with a rag under the chain to collect any dirty or excess liquid apply by spraying liberally onto the chain where it comes into contact with the rear cassette, while rotating the crank in a counterclockwise direction. This will ensure an even amount of degreaser is applied to remove any excess buildup of dirt and grime on the drivetrain once applied allowed to remain in contact for one to two minutes, the liquid will start to soften and lift dirt grease and oil from the chain easily to remove heavier stubborn buildup of grime.

You may need to agitate with a brush spray with clean water from a hose and dry with a clean cloth or towel. If you’re in a hurry and don’t have access to water, you can simply wipe off the chain with a rag cleaning. Your chain regularly helps to reduce, wear and tear and ensures optimum performance of your drivetrain finish line one step: cleaner, lubricant. Okay, we have all these loops. Why would I want to use one step? Well, one step is a great product. If you just want to lube your chain and go ride, you want it simple, you want it easy.

This is the product, because when you apply it, it has a very aggressive penetrant that gets in and pushes all the old lube and the accumulated dirt grit grime out of the park with your ever-moving and leaves behind fresh nice, blue you’re ready to go so so a good way to think about. It is a lot of times, we’ll wonder. Well, how often do I remove a window every? What should I be looking for? Well with one step, all you’re really looking for is when the chain gets dirty or dry. That’s it! You just want to apply some more.

If you want to worry about cleaning the changes spray on some one-step, it’ll penetrate in there and push all the other junk out, leave behind nicest fresh lubricant and you go right so that wet once that is a wet style lubricant. So it stays wet on the chain and in some drier, dustier climates. You may find that it’s dirty some fairly, often and so you’re applying and if you find yourself a fun day or you’re, applying blue more than you like then try our dry Teflon lube. It attracts less dirt because it goes on the chain wet but dries.

But you’ll notice with the dry TEFL new band does not have a built-in cleaning function like the one-step, so eventually that chain or part will accumulate enough directed only to be cleaning. You’ll need to use one of our degree search, see our degreasers and the videos on those four good explanations there. But if you want a one step, one product solution to keeping your parts running smooth and clean, then this is a very popular. The folks who just wanted easy and I want to get back on their bike and go ride.

The finish-line pro chain cleaner, makes it possible to clean your chain in under 60 seconds, without removing it from the frame with three spinning brushes side plates covers a metal, wear, magnet and no drip angle. A clean chain is only a minute away to use the pro chain cleaner start by filling the unit with citrus or multi degreaser to the fill line to clean, put the bottom of the unit under the chain and depress the chain, with the top secure, with the wires trap closure with the chain near the rear.

Derailleur that pedals slowly for approximately 20 revolutions to fully clean the chain. When clean under the wire strap closure to remove the unit, use a moist rag to remove any residue left by the degreaser, then you can remove your chain and go for a ride.

All right we’ve got today, unboxing of the bicycle chain: cleaner brush set a special series of bicycle right up there at the top. I, don’t even know what the name of this is on Amazon, but you’ll notice. What I’m talking about, because it will be the one that I post this review on. Oh man, this thing is like the cheapest feeling thing I’ve ever seen, and it’s it’s tiny. You know I expected it to be cheaper than the the park clone. You know these little tools, it’ll get the job done.

They feel super cheap. No man I mean what do you want for free? Yes, next up, we got the chain cleaner. It’s so throw that aside. You know it will open this just slide that over slide, that back I think you slide that back. That is because, oh that is like just complete crap um, the brushes seats slide this and because on sideways- and how does this go on here? Alright, that doesn’t totally make sense. Okay, here we go that has to go on after that’s, okay, so that’s actually holding that closed.

That makes sense. That’s actually not a terrible design. You know inside you know these. Don’t these don’t feel, though you still feel terrible. This little wiper here does feel terrible, but the proof will be in the pudding. Let me get it out on the bike. You know a lot. People like this is obviously a park clone. Oh yeah, Park Tool want to be at about a third, the price, and you know honestly the Park Tool. It’s not that fantastic. We built either though it is like twice the size.

So that is something to be said. For that I mean I. Guess if you’re paying for plastic by the pound, then you’ll want the park, but there it is. Let’s get it out on the bike and see how it feels that way, but the initial impressions super cheap feeling, but not necessarily that much worse than the park. So now that I have the super cheap, Amazon park tool, knockoff chain cleaner outside I’m, giving it a little workout. My chain is not real dirty since I conventionally cleaned it just a little bit ago, but it’s a good starting point.

So getting this thing working here and putting it together, I gotta, say I’m actually pretty impressed with this thing. You know once it’s all snapped together and the handle is kind of locked on there. The thing feels relatively solid and when you kind of start turning the pedals there, it doesn’t feel like you’re gonna, pull anything a partner or anything like that, and it really does scrub the chain from all the different directions. So you know I’m real happy with this product, for whatever I paid for I think likes eight dollars, a plus, of course, like I, do for nem reviews or any of my project builds links for products used.

And/Or products, reviews, door tools used, camera gear are in the description below use of them does support the channel, so that is greatly appreciated. Alright, good luck.

White lightnings, the trigger bicycle chain: cleaner, I, bought the degreaser and chain cleaner at my local bike. Shop I needed the cleaner for a sticky shifter and they didn’t have an individual can of the cleaner, so I bought the set it’s a 14 ounce can and it comes with an extra straw. I can already rave about the job. The chain degreaser did on my shifter this 18 year old shifter, with about 30 000 miles on it is again shifting crisply. This is for outdoor use, it’s extremely flammable and the vapor is harmful.

The degreaser gets great reviews on Amazon. It costs about ten to twelve dollars for a 14 ounce. Can whether it used says that you could clean 10 to 12 chains. The packaging says that one can will clean 30 chains. Two screws hold the chain cleaner on to the can the Amazon reviewers of the trigger in the cleaner combo, mostly love it. There are a few that really hated it. I checked out the reviewers profiles and all the reviews look like they were legitimate.

When the trigger is pulled, the casing closes it clamps over the chain, both brushes spin when backpedaling on a chain. It goes through in this direction. It exits through this piece. There’s a plastic piece. You can see that don’t push the end of the straw beyond that piece. That piece prevents the chain from hitting the straw. The one star reviews complained that the straw was not flexible, that it didn’t fit into the nozzle or the nozzle popped off the can.

There seems to be two schools of thought on how to use this. You can clamp down on the chain spray until the fluid is in this reservoir, then backpedal and run the chain through the cleaner until the fluid dries up. The other is to clamp down on the chain. You press the top of a can, while backpedaling the chain two to three revolutions through the cleaner I, had to get a feel for the proper tension to clamp down upon the chain. I’ll show some before and if they’re clean pictures shortly.

I had no problems with the straw or the top popping off. Those reviews were from three or four years ago, so I’ll presume that the manufacturer has corrected those problems. One of the other complaints was that people didn’t seem to be coordinated enough to hold the cam, pull the trigger push the button and turn the petals at the same time. So if you can’t pat your head and rub your stomach at the same time, maybe this isn’t the chain cleaner. For you, white lightning says you don’t have to wipe the chain down afterwards, however, I thought wiping it down left a better end result you you.

That concludes the review and demonstration of the trigger I hope you found this video helpful. A thumbs up is always appreciated. Click on the channel name know how now to find other videos and thanks for watching.