3 Good Gun Maintenance – Vises

I’m john mccoy with 85 41 tactical and. We’re here today to give you a short review of the tifton best gun vise you. Guys have seen this vise before on some. Of our product reviews and also on mail. Call mondays every now and again it is. Actually a really useful tool in our shop here now the tipton’s best gun vice. Can be adjusted to an extremely wide variety of firearms i really can’t think. Of any a shoulder-fired rifle that you. Really can’t fit this thing to starting. At the front here everything uses these. Big knobs to adjust and tighten down so. It’s all to listen adjust very fast we. Have the front cradle up here for the four end of your rifle or shotgun and you can undo this front knob and slide. It forward or back to wherever you need additionally you can undo this knob. Right here on the cradle and you can slide it up or down at an angle and. There are some detents in there that it skips over and you can set through a. Pretty wide range got to loosen it up a. Little bit more you can slide it through a pretty large range and get this thing. Really set wherever you need it when you get it where you want it and you lock the knob down there are little detents in here that keep it from sliding once. You lock it down so you don’t really have to crank it down hard but you can. Get it set in and you’re pretty good to go on the back here this is the portion. That really gives it the vice name now there are two knobs that allow you loosen this up and slide this portion forward or back on the aluminum track in. The base and once you get it set to where you want the buttstock to be you have two cams here on either side they. Have these big locking flipper levers on. Them what you do is initially you start with the levers in the up position and you use these black knobs on either side. To adjust the pads to get them fairly. Close to the stock you then flip these levers down and it cams those pads in. And applies pressure to your stock and it really locks it in there i mean you can see i can lift the back of the i sat by it so it’s really holding the stock in fairly sturdy and because these. Are just in and out if you’re working with a really fine wood stock and you don’t want to worry about mari you can use pretty light tension if you’re. Working with the tactical rifle that’s got some weight to it or you’re really going to be doing something that’s going to be moving the rifle around you can increase the tension and really crank that down additionally there is padded. Material in the middle here to protect your stock if you’ve got a really good angle on that stock on the toe then it’s. Not going to get nicked up or torn up now one of the really neat features of. This vise is it was designed to allow. You to work on ars as well very easily. Now you see we have an ar-15 in here and one of the primary ways to clean an. Ar-15 is to shotgun the rifle open that. Way you can just slide in your bore guide you can run your rods in etc and. You don’t have to fully disassemble the rifle they see it cleaned ars for a while know that when you take the upper receiver off it’s usually flopping around it always takes one hand to stabilize the upper while you’re using the other hand to try to run the rod and manage patches and all that and it just it can be kind of troublesome i you make. Do but you shouldn’t have to well on the. Tipton’s best gun vise they include this nifty little l-shaped bracket here and. What i like to do with it is set it with the short side up slide it back underneath the trigger guard and then lock it down and it will hold the ar in. Shotgun fashion so that you can put your. Bore guide in here run your cleaning rod etc and be hands-free if you want to put. It back down to work on optics or something it’s really easy to slide out of the way lock back down push your pin through and you’re done also you can see. On this there is a long leg you can flip. This the other direction so the long leg. Is up if you’re working on something like side by side or over-under shotguns. And you want to be able to set it up that way you can do so this vise offers. You a ton of options it’s got some nice. Recesses down here on the base to give you a place to put solving bottles patches attachments whatever the. Only thing that i really wish it would have is i wish it had some kind of notch. Or cradle on the side so i can drop my cleaning rod into that and not worry. About it rolling off the workbench but other than that it works very well as i. Said it clamps a rifle in very securely there’s really no worry about your rifle falling out of this this ar is clamped. In here so tight i would take an earthquake to knock it out it really is fairly well secured now to the drawbacks. First of all the cost on this runs right. About $90 you can catch them on sale at midway every now and again and for. Ninety dollars you’re getting a very nice design but they use some fairly lightweight materials this is all molded. Plastic pretty much the entire thing with the exception of the places where your rifle. Actually contacts it is plastic that it. Has rubber pads where your rifle is going to contact the cradle and then the. Thumb screws are the knobs here all have. Metal studs on the other side that they. Screw into and they have metal inserts in the actual knobs themselves so you. Don’t have to worry about breaking the knobs unless you really do something stupid but the plastic is fairly. Flexible you can squeeze on it and feel. It move when you tighten the knobs down sometimes you’re worried about cracking. The plastic it hasn’t actually been an issue but it’s always a fear in the back your mind also when you go to cam the. Levers down while they work and they. Hold the rifle very well you can see the. Whole assembly up here flex when you cam those levers down and it really it’s a. Little bit more flex than i’d like to see overall the tipton’s best gun vise. Does exactly what it was designed to do and it does it very well i’d like to see. A little bit higher quality materials but my fear is that would raise the price considerably and at ninety dollars. Were already on the upper end of what i. Think is probably an acceptable price range for this kind of product. Here however it makes your cleaning jobs a whole lot easier it makes maintaining your weapon a whole lot easier since you no longer have to worry about it rolling around on the bench or getting knocked off and really if you’re doing weapons. Maintenance on a regular basis this is a great tool to have additionally for us. It allows us to lock a weapon in so that you can see it and i still have my hands-free to do various different tasks and show you different things on a weapon system so for us it works very. Well if you’ve got any questions or comments on the tipton’s vesica inviting. In the comment section below or send them to us on facebook or twitter if you’ve liked this video please give us that thumbs up if you want to get one of. These of your own we’ll leave you a link in the description below on where you. Can go to pick one up for yourself and. If your subscriber thank you very much. If you’re not please subscribe and finally get out and shoot.

How’s it going guys, so we’ve been shooting a lot of USPS still challenge. Three gun then get the guns nice and. Dirty functioning really reliable i. Needed a gun vise so i walked into my. Local gun shop and they had tipton’s. Ultra gun vise really nice unit modular. So they could do a lot and i believe the. Can look like it will do conventional rifles break open shotguns modern sporting rifles crossbows upper receiver. Assemblies bull pups compound bow. Handguns and muzzle loaders it’s got. Some steel rails all modular the clay. Clamp width is two and a half inches four inches on the hike elevations got. Adjustable feet if you have a bench. That’s not flat maybe you’re going to do it on the ground or something i don’t know but it looks like it’s got all the bells and whistles a couple things i like. About it the trays are nice they snap in really easy seemed like it’d be really nice to clean holding your coals or both whatever small springs set screws pins. All room for that here everything get it. Nice and tight again it works for several platforms this is my. Lancer systems /jp 22 it’s in a little. Bit of rework and put a different optic on it with different modes muzzle break before this weekend’s steel challenge match which is eating up got a couple. Co-workers involved in there’s a lot of. Quick guys shooting in this room fire steel challenging that we put together really excited to keep it competitive. Yeah so one of nice things about this. You know you get either clamp it you. Could drop this down knobs got a great. Purchase on me could put a lot of torque into them I’m still a little bit tight. Going flying everywhere i imagine the more you use it the easier. It will start to function go ahead and. Pop the hold down charging handle now you get your floor. Type start running your rod through their jag’s whatever patches whatever. You use this is a really nice gun really. Expensive to build 10 22 is all you need. To do rim fire steel challenge stock 10. 22 should be able to do everything this thing does however if you are going to. Build an ar platform and rim fire hyper. Fire triggers a must have it tried. Everything nothing seemed to have the. Hammer impact to set off those rim fire rounds this hyper fire eclipse i have in. Here it’s the coated on the highest end. One talk to guys the hyper fire they. Figured it would work i had them test a. Bunch of them send me the best one of twenty doesn’t send the gun now i really. Like it really satisfied with the customer service and how quick they got it out to me and its function flawlessly. Simply put it on in not one failure to. Fire no life strikes really brutal nice. Trigger another thing that this. Particular vise has on it and again to. Clamp this hexagon carbon barrel and the. Lancer systems carbon stock is kind of pain this thing has a ball mount. So these articulates really nice it’s. Going to get a little dirty so it’s good that i got this needs a little bit of cleaning being a rim fire there is a. Trigger stop you know you should be able. To dry fire the trigger have arrived this different catch bolt catch release. For the rim fire setup it won’t work here but I’m sure I’ll put on my. Center fire rifle which is also a tricky. Gun to mount and see how that functions. But tipton ultra gun bites so far I’m. Really satisfied i like it seems really. Solid i mean this will probably be a class gun by you ever need it’s nice to see that they. Upgraded from their best gun bias or. Whatever it is so I’ll put my shotgun my. Pistol and my center fire rifle on there. And we’ll test out this hammer stock. There also is some sort of bolt tear down. Think on this mag well vise i probably. Won’t get into that if you get one you can read the instruction and see how that goes i don’t know how it goes yet but yeah we’ll put the next gun on alright so I’m. Going to kind of freestyle this one like i said I’m still really new to the. System but we’ll go ahead and put my center fire rifle in here by three gun. Really nice gun been really satisfied. With this thing so far it’s got it tuned. In june working really well so go ahead. And kind of awkward I’m doing it on the. Opposite side of my bench thank you this. Guy is locked down the frame and again. This is the kfs industries tac mod stock. Really nice unit daniel horner runs it if you’re familiar with three guns for a. Really nice modular it’s got adjustable cheek piece and just how far you want it. Out it does have this really thick limb. Saver butt stock pad which is quiet. Aggressive for two to three it does get. Hung up on your shirt sometimes here or. You’re shooting jersey i noticed daniel doesn’t run this on his. Rifle so i like it for now it’s pretty. Comfortable to shoot like that but it does get hung up on your shirt if you’re maneuvering the gunner getting it up. Again raise the front just lift up here. Go ahead and tighten that guy down and. Attack the clamps up. These trays will snap man i guess we don. That from there but the inner lock into. The mounts which is really nice so you. Get everything really tight if you need to be don’t need to in this situation. One thing about this rifle i want to. Show the hammer stop i do have jp take down pins in this gun. And there are the oversize tightening pins, so they are tough to get out this. Gun like it says that’s kfs industries. Stock really nice steiner 1/2 for scope. Nice for now lancer systems upper lower. Receiver carbon hand guard is a 16 and a. Quarter inch proof research carbon barrel jp systems titanium break all jp. Low-mass bolt they’re silent captures. Spring this one’s got the elf man tactical 3 gun trigger really nice. Didn’t work so well in the 22 works flawlessly in hair amazing trigger. Really liked it i got kind of short finger so i didn’t go with the flat face i do have a different grip. Coming this is just like a mil spec grip so is jp take down ends make the receiver. Really touched which is really. Nice you know if you don’t have a. Matched machine upper lower receiver i. Would get those work really nice go. Ahead and lower this down we could break the gun open a little further you justin. And this is a little tight going to. Clamp that down and this is an awkward gun to take apart you might have to take. The receiver off to get to this hammer. Deal which looks like we do crack this. Guy loose take the upper off so this is. The hammer stop it looks like in the. Brochure is supposed to go all the way down flat for some reason it’s not on this gun but. If you wanted to play with the trigger do some dry fires test trigger I’ll do. Some weight pulls on it that stops it. From impacting the lower receiver. Marring it up saves pan on trigger. That’s a really nice feature i like that. This is some sort of very weird it’s not. A hard rubber it’s more of a soft. Plastic so you could probably do this forever and it’s going to break that thing which is really nice so again this. Is with center fire rifle we’ll go ahead and throw my shotgun on here next see what it sees how it grabs it should work. Flawlessly alright we’ll go ahead and. Put the bread in here right at 1301. Really nice gun i did the modification to it we’ll go ahead and remove the mag glass out of the way and need that i did the loading port i. Did a lot of cylinders head fabrication and professional racing all different. Levels so i got in here with the grinder. Polish it up made quad loading much. Easier really happy with that this comes got a lancer systems i think it’s the +5. To carbon fiber really nice. Deal i could probably go back on the a. Bit and pull this tray out extend this a. Little more leverage on it. Yeah fairly simple fairly easy how much you. Do on a shotgun but if you want to take the tube out flip it over you could. Probably this probably would not even be. A bad way to do your modification to the. Loading port if you wanted to you could. Probably get real close to describe the receiver going there at the grinder dremel whatever your cover you’re going to do it go ahead and attack that so. This is the shotgun beretta 1301 lancers. Systems to so far as convent flawless i. Really like this come to the money hard. To beat it’s not a turn tactical but it. Works really nice so the last gun that. We’re going to install on here is my block g 34 put some zebb parts on it. Flared magwell i put our mar on it i do. I will run it in limited division pretty. Nice gun i like it i did order a 2011. But this has been working fine for now. Really it’s really nice kind of actually. Did a grip on here it’s got like a. Really velvety the lure type finish sub. Triggers of mag well zip slide barrel. All that parts again this is about the. Vise and go ahead and move this by some places prop this up see if we can grab it. By the lower part of the receiver. It’s like you can its enough bite on it. And it’s this damn sure wants a walk around go ahead and pull out this. Chamber flag and dry-fire go ahead and. Pull the slide off there yeah you put. Your caddies back in here i do have to. Clean this up go break it down. Simple easy you go in here and clean. This flow it out i use a lot of alcohol. To clean my guns i got a little compressed air canister throw some. Isotropic 70% in their rinse everything down realize if you don’t have a ultrasonic cleaner that removes. Everything and it’s really pretty safe on most finishes i would check before. You put on anything like spray paint but. Works well for me anodizing powder. Coating works fine so this is the. Tipton’s ultra gun buy so far you seem to put on rim fire center fire rifle. Shotgun pistol supposedly to put a. Crossbow on it palm combo all kinds of different things. Nice units solid doesn’t move around he. Could really get in there and run a brush or patches through something pretty aggressive leaves really pretty sturdy i even have it on this slippery. Surface here and it hasn’t moved around much so get all the adjustment nice unit. Chipton good job hope you guys enjoyed. This i did paint a hundred and seventy. Nine dollars in my local gun shop i try. To support those guys however you guys. Are probably really good at shopping if you searched the right sites amazon. Natchez midway you get them in one. A Hundred thirty-one hundred and forty dollar range over to local gun shop paid 179 for but happy to have my local gun shop. Cos when i need something in a pinch. They’re there hope you guys enjoyed. Enjoy shooting have fun be safe so you. Got the next match hopefully have a good one. You.

Hey guys midnight range tm here i wanted. To bring a quick review to the channel. Tipton ultra gun vise a few weeks ago i. Got a flyer in the mail for a midway and. This bad boys on sale right now I’ve. Wanted a gun vise for four years now. And i never wanted to buy a cheapie one. I wanted something nice but these were always in 150 dollar range or something like that a little more expensive than i wanted to put out for at the time so 99. Bucks is a killer price and so i brought. It home put it together i mounted a rifle in it once just to sort of get a feel for it but this summer once i get out and shoot some more I’m you know I’ll have a better idea of what’s going on how it works and use it on a couple different rifles so you know. Might do a secondary review then this is. Just sort of unboxed review it is. Solid it’s really nice mm-hmm it’s heavy. It’s really sticks in place it’s got. Some rubberized feet on the bottom the you screw on they have some bolts you. Can actually take those out and bolt it straight to a bench too if you want to. And then you know it’s a solid as your. Benches so just a couple of quick things. That go over it is sort of it is a polymer but it is a really sturdy. Polymer i wasn’t really sure what to. Expect from it’s not just like an injection molded plastic ii kind of. Hollow feeling it really is pretty solid. The basically it comes totally just a. Sound like disassembled you’ll get the rails and these rails are really like. Really thick it’s really sturdy it. Doesn’t have any give to it at all this this and this is all. Unattached when it comes these trades just pop off which is pretty cool. They just pop on and off really you know sort of like you know if you’re. Working on something you put your screwdrivers or your dyes or whatever the hell you want in there you know your punches or you know screws springs all. That kind of you know boing all that kind of little stuff stick them in there so you don’t lose them what would be nice too is to maybe cut a you know have. The magnets that are flexible what i. Want to do is actually get some of those and sort of superglue them into the. Bottom so that way there’s a magnet in there you can just drop a screw or a bolt or something in there and it’s gonna stick so that’s one thing i want. To do quick which is nice. The this and the actual vise parts. Unscrew and it’s basically like a. C-clamp underneath you know and it does. Really tighten down well it does a good. Job you know there is when you tighten. It obviously there’s a little you see you do see some bending of the tubes but that’s you know it is what it is it does a good job and it does hold up well the. Grips the vise grips are they do have a. Rubber cover on them and they’re a nice. Soft rubber i can’t see them marring. Anything i feel like it’s gonna do a. Good job and it’s soft enough to have a really good grip to it they do have a. Screw on the back that you can’t see, and they raise up and you can take them off. Obviously but they raise up so they do. Come up pretty high so that way you can. Put the back up and angle it down for cleaning so you’re not having any solvents or oils or anything run into the action of your rifle this is an. Ar-15 mountain obviously if you didn’t know that the ar-15 mount does pivot. Some screw it and pivots this is. For your ar-15 bolt take your bolt out. Hooks in there and it gives you the. Ability to clean out your bowl this is. Unbelievable it’s pretty cool and this. Is a hammer stop you actually put your. Air fifteen through the mag well there the magwell goes over top of this it sits here and then you can lift this up. And position it wherever it’s supposed to be positioned and that way if you’re doing trigger work or putting a trigger in say you’re polishing your trigger and. You want to check functionality when you. Pull the trigger and the hammer drops it’ll drop against this and that way. You’re not doing any undue abuse to your. Trigger okay so it’s just a you know. Soft plastic kind of rubbery plastic so. That’s really cool i thought that was really neat so i don’t think there’s a lot more to say other than that i just thought it was a really kind of a fun product to review especially. While it’s on sale i did see two that they are on sale on amazon for the same. Price but you know either way. You want to go you could do that if you. Got to order something from amazon anyway why not but i appreciate the. Appreciate you watching appreciate you checking out the channel midnight range tm i do live chant live chats sunday. Nights eastern 10:30 you check me out on. Patreon if you feel the. Urge to some help support the channel which is always appreciated. Check me out we do a lot of questions. And question and answers on sundays food and guns which is cool I’m a chef so. Come and check it out also check out gun channels comm they’re. Working on the website as of the video. Date right now, and they are going to be working on the mobile aspects of the site which is awesome so come check out gun channels comm tons. And tons of people it’s all member run and lots and lots of fun people lots of. Good information lots of awesome knowledge on firearms and guns and damn. Near anything, you might have a question about there’s somebody there that might that would know it so thanks for visiting the channel i hope you do so. Again and have a great day.

Everyone else here with house of guns. Calm and I’ve got another non-shooting. Review for you here this is kind of done. Simultaneously with the last one from ctk precision got a few products for them i want to show you but this video is done by me with house of guns calm. For arms vault calm the guys at arms. Vault were kind enough to help us get. Our hands on this product so thank you greg with arms vault for letting us check out this fantastic product totally. Impressed it’s a lot of times in the shooting industry you can get. Excited about something because you’re like oh yeah that’s neat but sometimes there’s a product that comes along that you just get totally geeked about because it’s better than what you’ve used in the past you know you see you always have your way of doing things and then you realize wow there’s a better. Way of doing this and sure enough we. Found one of them today the last review from house of guns comm i showed you the. Ctk precision p3 ultimate shooting risk. Complete package right here we talked. About the front yoke of the rear cradle or the rear platform that that fits on. To the frame here and slides on with the sleeve nice big adjustment knobs everything easy to use product and solid. As a rock i cannot emphasize that enough how solid this stuff from cdk precision. Is so i wanted to do this one on behalf. Of arms fall comm because this is. Something that i think they would be very excited about too just like i am so. We have this whole package here right i don’t want to be redundant, but we have this whole package of the ultimate. Shooting rest and i talked about how easy the sleeve is it slides this is how. It came the bottom the rear rest the rear cradle was already on the. Rest when i got it in order to take it off you would remove of the rear adjustment the rear shoe down here so but the cool thing is using. It as a vice even with an ar-15 that’s. That’s heavy on the bottom product here you have the magwell don’t even if you have a magazine in it makes it even longer and then the grip which comes way down a lot of shooting rest side views that’s always my problem shooting an ar you’re bumping into the frame plenty of room on this sucker that is not an issue at all but here we have today an ad on the. P3 ultimate gun vice now you would see. That the name is familiar you could get this package in one of two configurations you can get it holes with. With the frame and the gun vice say well maybe you know i work on them a lot but. I do a lot of bench shooting exciting stuff then you know i do it one and done and that’s fine so I’d rather have the vice i could work on stuff or you know. You say well i do more shooting that i go working off of a vice so I’d rather order it as a whole package with the rear cradle as a shooting rest and not as a complete vice package well what ctk does is they allow you to buy these. Add-ons let’s say you bought it as a. Rest and you say well I’d like to have the possibility to use it as a vice as well. The cool thing about that is that you can say okay well i can buy this in. Addition to this and use it. Cooperatively alongside of it so here. You have it’s essentially a clamp you can see the inside bracket here that. Fits around the one-inch square tubing. The adjustment clamp crank handle right. Here is huge that’s like three and a. Half inches there you’re not going to have any issues cinching this down and the same foam that we talked about on the shooting rest over here like this. Guy right here they use for protection. Of your firearm so if you don’t have a synthetic stock gun that you want to work on like this ar-15 let’s say you have a nice wood monte carlos porter stock something like that you say okay well I’m going to put this in a clamp i don’t want to hurt it this is soft foam you are not going to. Do any damage to your nice wood finish on a nice rifle if you have one so. This is attended to go along with the. Ultimate shooting rest that’s why it’s called the ultimate gun vice and so what i want to do here is show you how easy it is with the previous format with the. The ultimate shooters rest and the rear cradle here how easy it is to put this to put this vice to put this vice. Fitting on and use it as if we. Were going to get ready to work on this gun and put it in nice and solid so you. Have i showed you the clamp the tool. Hanger here the foam that would. Grip it as it clamps down you see and then there’s a simple band on the bottom that helps provide tension to hold it. Around the frame so you’re going to want to loosen it up enough so that open it. Will fit around the frame but this is. The awesome part this is what i love about this i want to loosen up the rear rest with the knob there the adjustment. Knob slide it up you guys see how it. Just has that sleeve it slides up and there we’re open in the back here I’m. Going to take this clamp it together slides it over put it in place put the. Gun where i want it I’m going to get it right on the meat of it there so it gets it nice and solid and all I’m going to do is tighten it up and you don’t have. To you don’t have to go crazy with it you won’t have to cinch it down you get it snug and it’s going to stay this. Thing is not not going anywhere it’s not. Even sliding down a device there so i can put some pressure on it hit it hard i know this isn’t a gun that I’m going to hurt so i wanted to show you that but this thing is fantastic and it’s not. It’s very rigid it’s very strong just. Like the rest of the frame of the rest is but it’s very simple to use and very. Very user-friendly it came totally assembled so all i had to do was figure out okay i need to slide this thing forward let’s say you want to. Break it open your ar you want to work on it open and this is cool because. You can use the rear rest in cooperation with device so I’m going to pop this. Hinge pin out we’re going to open it up. And I’m going to set the rest there. Tighten it up tighten that up a little. But so it’s not going to slide around and you have a vice there open up ar you. Can work on it you want to move the bowl whatever you feel like you need to do and everything’s right there run your. Cleaning rod down through it take it. Apart take the fore-end apart this thing is not going anywhere. The nice thing about that is we talked. About how rigid the shooting rest itself is how heavy it is how much weight it. Has to it the vice works in cooperation. With that so you have a nice solid base. That you don’t have to worry about toppling off the table be a top-heavy it’s nice and wide at the bottom and. It’s not going anywhere you could leave it overnight i mean make sure it’s safe where kids are going to get to it but it’s that easy then to remove it I’m not. Going to go through the trouble putting the bolt in just because of time here. But I’m going to move this back out of the way loosen this up just the tab. Slide it out pushes the pin in and loosen. This up enough that i can sandwich it. Together the top pull it off slide it. Back and boom I’m right there. Something that comes to mind with this is breaking it a new rifle at the range. And you know the one thing we like about. This that we set in the shooting rest review is that it is so it is so sturdy. But does not get in the way of the. Shooter getting comfortable on the rifle in order to get a good sight picture and. A good cheek weld to the top of the comb here so let’s say you’re one to break in. A rifle in your shooting once run in a. Patch through the bore shoot again run a patch to the bore and you go through that whole process well if you want to. Do that and you want a nice and sturdy so you can get in the grooves real well take this along clamp it on easy you can see how fast and easy it is to do and it works awesome the folks at c2k precision. Have thought through this so well and it is a very neat combination of the. Two so thanks to greg and arms ball comm. And hope this review has been helpful. Like all of our reviews please feel free to check out our youtube channel. Youtube.com slash house of guns you can. Also like us on facebook.com slash house of guns or follow us on. Twitter at you guessed it houses of guns. So thanks for taking the time to watch we hope this has been helpful and. Shooing everybody. You.

I’m john mccoy with 85 41 tactical and. We’re here today to give you a short review of the tifton best gun vise you. Guys have seen this vise before on some. Of our product reviews and also on mail. Call mondays every now and again it is. Actually a really useful tool in our shop here now the tipton’s best gun vice. Can be adjusted to an extremely wide variety of firearms i really can’t think. Of any a shoulder-fired rifle that you. Really can’t fit this thing to starting. At the front here everything uses these. Big knobs to adjust and tighten down so. It’s all to listen adjust very fast we. Have the front cradle up here for the four end of your rifle or shotgun and you can undo this front knob and slide. It forward or back to wherever you need additionally you can undo this knob. Right here on the cradle and you can slide it up or down at an angle and. There are some detents in there that it skips over and you can set through a. Pretty wide range got to loosen it up a. Little bit more you can slide it through a pretty large range and get this thing. Really set wherever you need it when you get it where you want it and you lock the knob down there are little detents in here that keep it from sliding once. You lock it down so you don’t really have to crank it down hard but you can. Get it set in and you’re pretty good to go on the back here this is the portion. That really gives it the vice name now there are two knobs that allow you loosen this up and slide this portion forward or back on the aluminum track in. The base and once you get it set to where you want the buttstock to be you have two cams here on either side they. Have these big locking flipper levers on. Them what you do is initially you start with the levers in the up position and you use these black knobs on either side. To adjust the pads to get them fairly. Close to the stock you then flip these levers down and it cams those pads in. And applies pressure to your stock and it really locks it in there i mean you can see i can lift the back of the i sat by it so it’s really holding the stock in fairly sturdy and because these. Are just in and out if you’re working with a really fine wood stock and you don’t want to worry about mari you can use pretty light tension if you’re. Working with the tactical rifle that’s got some weight to it or you’re really going to be doing something that’s going to be moving the rifle around you can increase the tension and really crank that down additionally there is padded. Material in the middle here to protect your stock if you’ve got a really good angle on that stock on the toe then it’s. Not going to get nicked up or torn up now one of the really neat features of. This vise is it was designed to allow. You to work on ars as well very easily. Now you see we have an ar-15 in here and one of the primary ways to clean an. Ar-15 is to shotgun the rifle open that. Way you can just slide in your bore guide you can run your rods in etc and. You don’t have to fully disassemble the rifle they see it cleaned ars for a while know that when you take the upper receiver off it’s usually flopping around it always takes one hand to stabilize the upper while you’re using the other hand to try to run the rod and manage patches and all that and it just it can be kind of troublesome i you make. Do but you shouldn’t have to well on the. Tipton’s best gun vise they include this nifty little l-shaped bracket here and. What i like to do with it is set it with the short side up slide it back underneath the trigger guard and then lock it down and it will hold the ar in. Shotgun fashion so that you can put your. Bore guide in here run your cleaning rod etc and be hands-free if you want to put. It back down to work on optics or something it’s really easy to slide out of the way lock back down push your pin through and you’re done also you can see. On this there is a long leg you can flip. This the other direction so the long leg. Is up if you’re working on something like side by side or over-under shotguns. And you want to be able to set it up that way you can do so this vise offers. You a ton of options it’s got some nice. Recesses down here on the base to give you a place to put solving bottles patches attachments whatever the. Only thing that i really wish it would have is i wish it had some kind of notch. Or cradle on the side so i can drop my cleaning rod into that and not worry. About it rolling off the workbench but other than that it works very well as i. Said it clamps a rifle in very securely there’s really no worry about your rifle falling out of this this ar is clamped. In here so tight i would take an earthquake to knock it out it really is fairly well secured now to the drawbacks. First of all the cost on this runs right. About $90 you can catch them on sale at midway every now and again and for. Ninety dollars you’re getting a very nice design but they use some fairly lightweight materials this is all molded. Plastic pretty much the entire thing with the exception of the places where your rifle. Actually contacts it is plastic that it. Has rubber pads where your rifle is going to contact the cradle and then the. Thumb screws are the knobs here all have. Metal studs on the other side that they. Screw into and they have metal inserts in the actual knobs themselves so you. Don’t have to worry about breaking the knobs unless you really do something stupid but the plastic is fairly. Flexible you can squeeze on it and feel. It move when you tighten the knobs down sometimes you’re worried about cracking. The plastic it hasn’t actually been an issue but it’s always a fear in the back your mind also when you go to cam the. Levers down while they work and they. Hold the rifle very well you can see the. Whole assembly up here flex when you cam those levers down and it really it’s a. Little bit more flex than i’d like to see overall the tipton’s best gun vise. Does exactly what it was designed to do and it does it very well i’d like to see. A little bit higher quality materials but my fear is that would raise the price considerably and at ninety dollars. Were already on the upper end of what i. Think is probably an acceptable price range for this kind of product. Here however it makes your cleaning jobs a whole lot easier it makes maintaining your weapon a whole lot easier since you no longer have to worry about it rolling around on the bench or getting knocked off and really if you’re doing weapons. Maintenance on a regular basis this is a great tool to have additionally for us. It allows us to lock a weapon in so that you can see it and i still have my hands-free to do various different tasks and show you different things on a weapon system so for us it works very. Well if you’ve got any questions or comments on the tipton’s vesica inviting. In the comment section below or send them to us on facebook or twitter if you’ve liked this video please give us that thumbs up if you want to get one of. These of your own we’ll leave you a link in the description below on where you. Can go to pick one up for yourself and. If your subscriber thank you very much. If you’re not please subscribe and finally get out and shoot.

How’s it going guys, so we’ve been shooting a lot of USPS still challenge. Three gun then get the guns nice and. Dirty functioning really reliable i. Needed a gun vise so i walked into my. Local gun shop and they had tipton’s. Ultra gun vise really nice unit modular. So they could do a lot and i believe the. Can look like it will do conventional rifles break open shotguns modern sporting rifles crossbows upper receiver. Assemblies bull pups compound bow. Handguns and muzzle loaders it’s got. Some steel rails all modular the clay. Clamp width is two and a half inches four inches on the hike elevations got. Adjustable feet if you have a bench. That’s not flat maybe you’re going to do it on the ground or something i don’t know but it looks like it’s got all the bells and whistles a couple things i like. About it the trays are nice they snap in really easy seemed like it’d be really nice to clean holding your coals or both whatever small springs set screws pins. All room for that here everything get it. Nice and tight again it works for several platforms this is my. Lancer systems /jp 22 it’s in a little. Bit of rework and put a different optic on it with different modes muzzle break before this weekend’s steel challenge match which is eating up got a couple. Co-workers involved in there’s a lot of. Quick guys shooting in this room fire steel challenging that we put together really excited to keep it competitive. Yeah so one of nice things about this. You know you get either clamp it you. Could drop this down knobs got a great. Purchase on me could put a lot of torque into them I’m still a little bit tight. Going flying everywhere i imagine the more you use it the easier. It will start to function go ahead and. Pop the hold down charging handle now you get your floor. Type start running your rod through their jag’s whatever patches whatever. You use this is a really nice gun really. Expensive to build 10 22 is all you need. To do rim fire steel challenge stock 10. 22 should be able to do everything this thing does however if you are going to. Build an ar platform and rim fire hyper. Fire triggers a must have it tried. Everything nothing seemed to have the. Hammer impact to set off those rim fire rounds this hyper fire eclipse i have in. Here it’s the coated on the highest end. One talk to guys the hyper fire they. Figured it would work i had them test a. Bunch of them send me the best one of twenty doesn’t send the gun now i really. Like it really satisfied with the customer service and how quick they got it out to me and its function flawlessly. Simply put it on in not one failure to. Fire no life strikes really brutal nice. Trigger another thing that this. Particular vise has on it and again to. Clamp this hexagon carbon barrel and the. Lancer systems carbon stock is kind of pain this thing has a ball mount. So these articulates really nice it’s. Going to get a little dirty so it’s good that i got this needs a little bit of cleaning being a rim fire there is a. Trigger stop you know you should be able. To dry fire the trigger have arrived this different catch bolt catch release. For the rim fire setup it won’t work here but I’m sure I’ll put on my. Center fire rifle which is also a tricky. Gun to mount and see how that functions. But tipton ultra gun bites so far I’m. Really satisfied i like it seems really. Solid i mean this will probably be a class gun by you ever need it’s nice to see that they. Upgraded from their best gun bias or. Whatever it is so I’ll put my shotgun my. Pistol and my center fire rifle on there. And we’ll test out this hammer stock. There also is some sort of bolt tear down. Think on this mag well vise i probably. Won’t get into that if you get one you can read the instruction and see how that goes i don’t know how it goes yet but yeah we’ll put the next gun on alright so I’m. Going to kind of freestyle this one like i said I’m still really new to the. System but we’ll go ahead and put my center fire rifle in here by three gun. Really nice gun been really satisfied. With this thing so far it’s got it tuned. In june working really well so go ahead. And kind of awkward I’m doing it on the. Opposite side of my bench thank you this. Guy is locked down the frame and again. This is the kfs industries tac mod stock. Really nice unit daniel horner runs it if you’re familiar with three guns for a. Really nice modular it’s got adjustable cheek piece and just how far you want it. Out it does have this really thick limb. Saver butt stock pad which is quiet. Aggressive for two to three it does get. Hung up on your shirt sometimes here or. You’re shooting jersey i noticed daniel doesn’t run this on his. Rifle so i like it for now it’s pretty. Comfortable to shoot like that but it does get hung up on your shirt if you’re maneuvering the gunner getting it up. Again raise the front just lift up here. Go ahead and tighten that guy down and. Attack the clamps up. These trays will snap man i guess we don. That from there but the inner lock into. The mounts which is really nice so you. Get everything really tight if you need to be don’t need to in this situation. One thing about this rifle i want to. Show the hammer stop i do have jp take down pins in this gun. And there are the oversize tightening pins, so they are tough to get out this. Gun like it says that’s kfs industries. Stock really nice steiner 1/2 for scope. Nice for now lancer systems upper lower. Receiver carbon hand guard is a 16 and a. Quarter inch proof research carbon barrel jp systems titanium break all jp. Low-mass bolt they’re silent captures. Spring this one’s got the elf man tactical 3 gun trigger really nice. Didn’t work so well in the 22 works flawlessly in hair amazing trigger. Really liked it i got kind of short finger so i didn’t go with the flat face i do have a different grip. Coming this is just like a mil spec grip so is jp take down ends make the receiver. Really touched which is really. Nice you know if you don’t have a. Matched machine upper lower receiver i. Would get those work really nice go. Ahead and lower this down we could break the gun open a little further you justin. And this is a little tight going to. Clamp that down and this is an awkward gun to take apart you might have to take. The receiver off to get to this hammer. Deal which looks like we do crack this. Guy loose take the upper off so this is. The hammer stop it looks like in the. Brochure is supposed to go all the way down flat for some reason it’s not on this gun but. If you wanted to play with the trigger do some dry fires test trigger I’ll do. Some weight pulls on it that stops it. From impacting the lower receiver. Marring it up saves pan on trigger. That’s a really nice feature i like that. This is some sort of very weird it’s not. A hard rubber it’s more of a soft. Plastic so you could probably do this forever and it’s going to break that thing which is really nice so again this. Is with center fire rifle we’ll go ahead and throw my shotgun on here next see what it sees how it grabs it should work. Flawlessly alright we’ll go ahead and. Put the bread in here right at 1301. Really nice gun i did the modification to it we’ll go ahead and remove the mag glass out of the way and need that i did the loading port i. Did a lot of cylinders head fabrication and professional racing all different. Levels so i got in here with the grinder. Polish it up made quad loading much. Easier really happy with that this comes got a lancer systems i think it’s the +5. To carbon fiber really nice. Deal i could probably go back on the a. Bit and pull this tray out extend this a. Little more leverage on it. Yeah fairly simple fairly easy how much you. Do on a shotgun but if you want to take the tube out flip it over you could. Probably this probably would not even be. A bad way to do your modification to the. Loading port if you wanted to you could. Probably get real close to describe the receiver going there at the grinder dremel whatever your cover you’re going to do it go ahead and attack that so. This is the shotgun beretta 1301 lancers. Systems to so far as convent flawless i. Really like this come to the money hard. To beat it’s not a turn tactical but it. Works really nice so the last gun that. We’re going to install on here is my block g 34 put some zebb parts on it. Flared magwell i put our mar on it i do. I will run it in limited division pretty. Nice gun i like it i did order a 2011. But this has been working fine for now. Really it’s really nice kind of actually. Did a grip on here it’s got like a. Really velvety the lure type finish sub. Triggers of mag well zip slide barrel. All that parts again this is about the. Vise and go ahead and move this by some places prop this up see if we can grab it. By the lower part of the receiver. It’s like you can its enough bite on it. And it’s this damn sure wants a walk around go ahead and pull out this. Chamber flag and dry-fire go ahead and. Pull the slide off there yeah you put. Your caddies back in here i do have to. Clean this up go break it down. Simple easy you go in here and clean. This flow it out i use a lot of alcohol. To clean my guns i got a little compressed air canister throw some. Isotropic 70% in their rinse everything down realize if you don’t have a ultrasonic cleaner that removes. Everything and it’s really pretty safe on most finishes i would check before. You put on anything like spray paint but. Works well for me anodizing powder. Coating works fine so this is the. Tipton’s ultra gun buy so far you seem to put on rim fire center fire rifle. Shotgun pistol supposedly to put a. Crossbow on it palm combo all kinds of different things. Nice units solid doesn’t move around he. Could really get in there and run a brush or patches through something pretty aggressive leaves really pretty sturdy i even have it on this slippery. Surface here and it hasn’t moved around much so get all the adjustment nice unit. Chipton good job hope you guys enjoyed. This i did paint a hundred and seventy. Nine dollars in my local gun shop i try. To support those guys however you guys. Are probably really good at shopping if you searched the right sites amazon. Natchez midway you get them in one. A Hundred thirty-one hundred and forty dollar range over to local gun shop paid 179 for but happy to have my local gun shop. Cos when i need something in a pinch. They’re there hope you guys enjoyed. Enjoy shooting have fun be safe so you. Got the next match hopefully have a good one. You.

Hey sup everybody phil at youtube. Friends urban art and had a few. Questions on the gun vise that i bought. As a result of jackin at my finger when. Cleaning my okay so i thought i would. Make a video is probably gonna be short because there’s not a lot about it to review but nonetheless it’s been. Requested so I’m gonna go ahead and take. A few minutes and I’ll go over my super. Fancy awesome gun vise so check it out i. So i don’t know if you’ve seen any of my. Videos before but there was a point in time that i cut my finger actually it was on the right hand which was holding. The camera but it was this side he can’t. It doesn’t matter anyways i cut it really bad and it was because i didn’t have the proper tools when i was trying. To clear jam in my a k so that. Prompted me to pull the trigger so to speak on a gun vise for cleaning my. Rifles I’ve got only a couple rifles. I’ve got an ak-47 and a ruger 10/22. Which i am totally in love with but had. Some comments and questions about my opinion about the particular vise that i. Bought so just got to get into it so. This is the tipton’s ti pto in the best kind. Of ice i guess in the world not sure. Actually where it’s made i know a big. Deal of trying to buy american right not sure my guess is for I’m not sure I’ll. Have to look it up but it’s not exactly sure the total. Length so hang on I’ll go ahead and. Measure it for you okay it’s a total length of this bad boy into end is almost it’s almost three. Feet it’s 32 inches so if you’re trying. To see if you’ve you know how long your bench or your table is it’s 32 inches in length use bowl probably about. 30 full or not I’m sorry probably about. 29 or 30 inches of actual length space. But it was pretty easy to put together. It essentially has a couple pieces so. These two pieces come separate and this. Whole module can it’s just controlled by these dials which there’s this rail down here and it slides them too so you can slide this whole piece front and back which is nice and then you can crank it. Crank it down and this is where the barrel will rest down on this end and. You can kind of as i pulled it all the. Way out i think i pulled it out too far. That’s what she said so anyways let me. Fix this real quick okay so i just kind of came off the track i pulled it too far back and you can slide it forwards you can tighten it down this guy as well. Slides up and down depending upon the height of maybe like the barrel or. You know i guess i never really screw. With it to be honest with you but you can pull this up higher here then tighten it down right here. What if you like as this metal piece also slides on the rail you can loosen that and it slides back and forth on. This little grid here and you can. Tighten it down so this would be like maybe further like where your trigger is or your upper receiver my rest on here. Or something like that and then back. Here has another rest for this stock and. This is kind of cool so these guys. Actually can push to tighten it easily so you don’t have. To screw these every single time you can kind of get it fitted for this for your. Particular stock and then went to tighten it down you just pull down on. Both sides and it kind of pushes it together and that’s kind of cool so I’ll put my. I’ve got my ak-47 out and I’ll go ahead. And put that in their kind of show you how that works okay so i just put my. Occasion here and you can see that it’s resting right here and i can you know slide that forward if i want but that’s a pretty good resting place i tend to usually put a towel down first or cloth. Or something over the top of this so that when you’re putting solvents and stuff in the top it’s going to come through your lower down here and you can. Drip down and i just try to keep solvents off this is like some sort of rubber polymer ish kind of thing so. Just for the sake of keeping it lasting longer and stuff they just cover it up you can see the barrels resting down here and in the back I’ve got the stock. In here and if i push down on these i. Kind of go in so now this is pretty tight and i can you can screw these just to make a little bit more snug so. Doesn’t move anywhere so that way when you start popping stuff off and getting. All crazy with your cleaning and all that you know your rifle stays in place. As I’m moving around super helpful. Keeping yourself and getting hurt I’m. Kind of doing this one-handed anyway you get the idea i mean now i can go ahead and strip this bad boy down it’s an upright position it’s easy for me to check the breech when I’m cleaning it. And all that good stuff because i got. Like one of those little safeties on you. Go into those breech lights i should i. Don’t know where the hell i actually I’ve got it over here just kind of walk. Around what’s up on this rank right here so it’s nice because i keep some tools. Kind of down here and you can put like patches and stuff in here i don’t really store anything and compartments but i guess you could and. Handed so i guess to be out there so. It’s nice because i can do stuff like what I’m cleaning the gun and everything i can make sure nothing going on i can. Shine my light down here and then you. No see viking yeah you get the idea. It’s a little dirty was at the range and. I got a i got to clean it but it’s a 8k. So you know it’s fine anyway it’s pretty. Good in retail on this thing i paid adventurer outdoors 99 bucks a little more than I’d really. Like to spend but compared to the alternatives that were really cheap and like the 40 50 dollar range. Were really flimsy and plasticky this. Thing’s pretty solid it’s got screws in there are holes in the base if you want to mount it to something you could it’s. Gonna mount all four corners and you. Now it’s its its pretty nice makes. Mixes life pretty easy for cleaning. These guns out so that’s pretty. Much all they had i really don’t know. What else to say about it other than it was a really worthwhile investment one. That’ll hopefully lasts forever and makes my life really easy when cleaning both my ek and my rigger and i. Do plan to get some other rifles and. Just notice that this was a loose i have to tighten that i also got picked. Something up for that so I’ll be doing a video on that a little optic for it so. Anyway that’s my tipton best gun vise. 100 bucks works pretty darn well is it. Worth a hundred yeah and that’s that’s. Up to you to decide i mean i know it’s kind of hard to drop that kind of coin for something like this but for me it. Was a pretty investment long-term at plenty is it quite a bit so that’s uh. That’s my review of my yeah my rifle. Cleaning vise so cool all right urban armed I’ll talk to y’all here.

Hey guys midnight range tm here i wanted. To bring a quick review to the channel. Tipton ultra gun vise a few weeks ago i. Got a flyer in the mail for a midway and. This bad boys on sale right now I’ve. Wanted a gun vise for four years now. And i never wanted to buy a cheapie one. I wanted something nice but these were always in 150 dollar range or something like that a little more expensive than i wanted to put out for at the time so 99. Bucks is a killer price and so i brought. It home put it together i mounted a rifle in it once just to sort of get a feel for it but this summer once i get out and shoot some more I’m you know I’ll have a better idea of what’s going on how it works and use it on a couple different rifles so you know. Might do a secondary review then this is. Just sort of unboxed review it is. Solid it’s really nice mm-hmm it’s heavy. It’s really sticks in place it’s got. Some rubberized feet on the bottom the you screw on they have some bolts you. Can actually take those out and bolt it straight to a bench too if you want to. And then you know it’s a solid as your. Benches so just a couple of quick things. That go over it is sort of it is a polymer but it is a really sturdy. Polymer i wasn’t really sure what to. Expect from it’s not just like an injection molded plastic ii kind of. Hollow feeling it really is pretty solid. The basically it comes totally just a. Sound like disassembled you’ll get the rails and these rails are really like. Really thick it’s really sturdy it. Doesn’t have any give to it at all this this and this is all. Unattached when it comes these trades just pop off which is pretty cool. They just pop on and off really you know sort of like you know if you’re. Working on something you put your screwdrivers or your dyes or whatever the hell you want in there you know your punches or you know screws springs all. That kind of you know boing all that kind of little stuff stick them in there so you don’t lose them what would be nice too is to maybe cut a you know have. The magnets that are flexible what i. Want to do is actually get some of those and sort of superglue them into the. Bottom so that way there’s a magnet in there you can just drop a screw or a bolt or something in there and it’s gonna stick so that’s one thing i want. To do quick which is nice. The this and the actual vise parts. Unscrew and it’s basically like a. C-clamp underneath you know and it does. Really tighten down well it does a good. Job you know there is when you tighten. It obviously there’s a little you see you do see some bending of the tubes but that’s you know it is what it is it does a good job and it does hold up well the. Grips the vise grips are they do have a. Rubber cover on them and they’re a nice. Soft rubber i can’t see them marring. Anything i feel like it’s gonna do a. Good job and it’s soft enough to have a really good grip to it they do have a. Screw on the back that you can’t see, and they raise up and you can take them off. Obviously but they raise up so they do. Come up pretty high so that way you can. Put the back up and angle it down for cleaning so you’re not having any solvents or oils or anything run into the action of your rifle this is an. Ar-15 mountain obviously if you didn’t know that the ar-15 mount does pivot. Some screw it and pivots this is. For your ar-15 bolt take your bolt out. Hooks in there and it gives you the. Ability to clean out your bowl this is. Unbelievable it’s pretty cool and this. Is a hammer stop you actually put your. Air fifteen through the mag well there the magwell goes over top of this it sits here and then you can lift this up. And position it wherever it’s supposed to be positioned and that way if you’re doing trigger work or putting a trigger in say you’re polishing your trigger and. You want to check functionality when you. Pull the trigger and the hammer drops it’ll drop against this and that way. You’re not doing any undue abuse to your. Trigger okay so it’s just a you know. Soft plastic kind of rubbery plastic so. That’s really cool i thought that was really neat so i don’t think there’s a lot more to say other than that i just thought it was a really kind of a fun product to review especially. While it’s on sale i did see two that they are on sale on amazon for the same. Price but you know either way. You want to go you could do that if you. Got to order something from amazon anyway why not but i appreciate the. Appreciate you watching appreciate you checking out the channel midnight range tm i do live chant live chats sunday. Nights eastern 10:30 you check me out on. Patreon if you feel the. Urge to some help support the channel which is always appreciated. Check me out we do a lot of questions. And question and answers on sundays food and guns which is cool I’m a chef so. Come and check it out also check out gun channels comm they’re. Working on the website as of the video. Date right now, and they are going to be working on the mobile aspects of the site which is awesome so come check out gun channels comm tons. And tons of people it’s all member run and lots and lots of fun people lots of. Good information lots of awesome knowledge on firearms and guns and damn. Near anything, you might have a question about there’s somebody there that might that would know it so thanks for visiting the channel i hope you do so. Again and have a great day.

The portable armorer’s device has been. Designed to give the shooter a fixture. That he can use either at home on his workbench or in the field to secure his. Guns for cleaning and servicing clamp. The clamps to the bench top insert the. Shaft of the vise to the hole so that. The club caves engage and tighten the. Nut and you’re ready to go the vise is the perfect servicing and. Maintenance fixture for all guns plant. The gun on the vise then the vise can be. Rotated through 360 degrees so the gun. Can be clamped pointing downward or the. Gun can be held level and the vise. Becomes the perfect scope mounting companion the vise makes cleaning and. Servicing an ar style weapon a simple. Task grip the gun in the vise remove the. Rear take down pin and a rotate device. That’s just at the perfect angle and. Lock it into place now you have full. Access to the trigger group the bolt and carrier assembly and you’re able to. Clean the gun with the muzzle angled down so the old gunk and debris run out. The muzzle and not back into your action and trigger group. You.

The high score armor advice is the most. Advanced and full-featured long gun. Cleaning maintenance and servicing. Fixture available anyplace although it’s. Designed to accommodate any style loan. Gun who specially had ar-15 style guns. In mind when we designed it first make a. Visual examination of your weapon to make sure it’s unloaded pull out the red. Take out pin into the upper receiver. Against the lower butt stock rear vise. Type it the foreign for advice clamp it. What do we have we now have easy and. Convenient access to every point on the weapon this includes the bolt group and. Everything in the upper receiver the. Trigger group the recoil buffer and everything in the lower receiver in addition cleaning it’s absolutely. Ideal because using only two hands the. Gun is now firmly held in place we can. Clean from the breech towards the muzzle and all the gunk and debris runs out the muzzle rather than running back into. Your lower receiver and trigger group it is in short the perfect the most. Convenient cleaning fixtures you’ll find. Anywhere. Your advice is perfect all smiles do we. Have a Remington. What we’ve done here is we’ve positioned the arms with the entire gun is a. Downward facing attitude and what this. Means is that pop the vault out now that. Can clean from the breach was the muzzle. And once again all the gunk and debris. Run out the muzzle rather than running. Back into your triggered roof in action there are two ways to adjust the angle. Two heads of the fixture number one is. To use the round holes as we’ve done. Here on the right or number two that you. Can use the slack as we’ve done here on the left you can adjust the angle two it’s absolutely perfect to service your. Weapon by simply changing the angle. Between the axial rail assemblies you. Can now work on the gun inverted devices. Also right along their respective rail. Assemblies through just to almost any. Length weapon devices are special because they are self centering when. Conventional vise one jaw remains stationary while the other one moves on. A self centering vise both jaws move. Together at the same rate in the same time, and they close exactly in the. Center what that means to you is that. When you lock your gun and this device one by centers on the other and the gun. Is always held dead center in addition. To protect the gun each drove the vise. As a 12 millimeter thick closed-cell. Nonreactive foam pad to protect the gun. From metal parts in the bottom of the vise there are two floor plates. Each floor plate also has a 12. Millimeter thick bone plan locks right. In just like that. Now you come as well protected going. Beyond that on the upper surfaces. Devices frame we also have foam padding. And then up here again when the. Axial rail assembly is the same reason. To protect the finish of your gun for. The times when it may be necessary to. Grip the vise directly on a barrel or. Barreled action we’ve supplied a pair of. Foam d blocks one block on each side of. The barrel with the barrel inside the b. Slide it down into the vise thank the. Vise and you’re good to go one thing to keep in mind is that the. Foam is temperature sensitive and the. Barrel should never be warmer than 150. Degrees Fahrenheit the base measures 19 inches by 12 inches. And is 14 inches high the extreme. Dimension when the axial rail with them. Was a fully extended is 32 inches and. Just the way it’s pictured here it weighs 24 pounds. The platform and the v-notch assembly. Add about two and a halves to three pounds. This is the setup with free shots. Sighting in the v-notch and one vise are. Installed please note that the vise is. Fully open the reason is that this. Fixture is not a designed nor intended. To absorb or attenuate any recoil firing. A gun clamped firmly in the vise can. Result in damage to the weapon damage to. The fixture and damage to the shooter with the vise open aim at the center of. Your target and fire a three shot group. Unload the weapon now mark the center of. The group you can use a marker or you. Can use one of the handy orange dots. That have been supplied with the rest. With the guns unloaded remove the caps. From the adjusting turrets of the scope. Firmly clamp the gun in the vise by. Moving device and using adjustments on. The fixture move the crosshairs to the. Original point of aim in this case that. Would be the center of the target now by. Using the adjustments on the scope only. Walk the crosshairs into the center of. The point of impact which has already. Been marked and in our case with the orange marker now the sites have been. Mechanically and optically aligned and. The gun is sighted in. You.

On the spot upkeep made easy the. Portable armorer’s vise delivers 100% frustration free cleaning scope mounting. And maintenance right at the range clamps to any bench top and secures your firearm with a padded nomar vise grip. 360 degree rotation provides free and. Easy access at all angles works just. Like the one you have in the shop in fact it’s heavy gauge machine steel construction makes it a winner for at-home use — providing the sturdy support and ready accessibility you need to properly service your steel order now.

Cleaning citing or shooting get a grip. On the master armorer vice from high score loaded with the ultimate and. Adjustability for unmatched versatility easy crank self-centering receiver and. Buttock vices can be set to cradle a wide range of weapon legs user-friendly. Front and back angle adjustments and 360. Degree swivel allow easy access to every. Inch of your firearm and four shot sighting or use as a shooting rest the. Included v-notch gun support attaches in a flash for an extra hand at the range. Or workbench the master armorer’s vice from high score is a sure shot order. Yours today.

Au programme. Nova restés bloqués mais le succès de cholet hausse ça fait bien qu’elle n’est pas prête. On était une galloise. Comme candidat au moins. Restez calme donc marquer une campagne. Jospin ou à peine. On rappelle que croyance. Le crime de l’avortement. Sobre on replante de brit air a commencé. La culture la culture du houblon.