Every beginner angler faces the problem of tying hooks. A lot depends on the choice of the knot: the effectiveness of the tackle, the breaking load and the number of bites. Below you will find 12 ways to mount a hook, which are suitable not only for beginners, but also for experienced anglers.

Blind knot

The easiest way to fasten to a hook is a knot based on a single loop. To tie it, it is necessary to put a loop in the ear of the hook, and then the sting should be inserted into it. This way, the hook remains fixed on the line, and the monofil is not crushed by many overlaps. This knot is excellent for mounting leads, as well as for attaching swivels and carabiners.

Bayonet knot

The best attachment is for a fuzzy cord, because the fishing line slips a lot, and the knot may not hold. To install it, you need to make a loop on the forend of the hook, with the two ends peeking out in different directions. The knot is wet and gently tightened. The result is a minimal diameter connection that holds fine wire hooks and models with a spatula instead of an eye.

Canadian Eight

For monofilament fishing line is often used the original knot – the Canadian figure eight. The end of the fishing line is slipped into the ear on the outside, made a turn around the fore-end, and then guided into the loop. Its name was given to the fastener because of the described figure of eight, which comes out at the time of installation. This knot is easy to untie, so the angler does not have to use scissors and deform the thin steel of the hook.

Fishing figure eight

Analogous to the previous method of attachment was invented by experienced fishermen. To use it, you need to fold the line in half and pass the resulting loop in the ear. The free end makes a movement around the line and returns to the loop, which is located along the hook.

Turtle knot

Simple to use knot looks like some kind of bakery product, so no one can describe the history of the origin of its name. Knit construction is simple: the fishing line is threaded through the ear, forming two adjacent loops. Around a large loop make a turn and wind the free end in a small loop. The resulting knot is pulled up and lifted to the ear of the hook. This knot is especially good for ice fishing. With its help, an additional hook is attached, which is above the mormyshka.

California Knot

This method of attachment resembles a figure of eight. It was invented at the end of the last century by Californian lovers of recreation at the pond. To mount it, you need to fold the thread in half and pass it through the ring. Next, it is necessary to make a turn around the cord and to enter the tip in the formed loop. The knot reliably holds both the fishing line and the braid, but has a small disadvantage – bulkiness.

Step node

For lovers of spade hooks, this is a real godsend. The first few turns are made around the hook, and the following turns are made along the shaft and the line, tightening the knot like a snare. Proper design keeps the hook in a vertical position, which makes it easier for the fish to swallow the bait.

Salmon knot

One of the most reliable and effective is considered to be the knot, which is widely used in fly fishing. The knot covers the hooks forend from several sides, so its quality always remains at a high level. In addition, it is almost impossible to untie the fastener, any loosening only tightens it. The free end of the line is passed through the ear, unrolled and made several turns around its axis, running into the loop formed near the ear. Then the upper loop is lowered to the hook and also passed through its free tip. The knot must be tightened with all the care to achieve a quality attachment. The intricate design gives an undeniable result.

Shark Knot

The simplest method of hook mounting, in which the bait moves freely on its axis. This method is popular when fishing in the water column on active types of baits. A simple installation consists of putting the cord or monofilament through the eye, 5-6 turns around its axis and the final direction to the last loop.

Gripping node

This attachment is exactly the same as the shark knot, but the end is led out in the bottom loop. The attachment is reliable when using any line as well as cord. Unlike its previous counterpart, it is possible to significantly reduce the number of turns in the grip knot, thus making it less bulky.

Tuna knot

The specialized saltwater fishing knot has caught the eye of big fish hunters the world over. The original way of knitting makes the knot truly unique. The attachment is strengthened by having two loops on the eye instead of one. The fishing line runs along the shank on different sides, and then goes down. The knot is best used on wide-ear models, which are often used in micro jigs.

Leash

This type of attachment is used to mount leads to the main line. It is successfully used in spinning fishing with spread tackle, as well as in whitefish fishing with a rubber band and bottom tackle. On the main fishing line make the usual knot and, without tightening, pass the lead through the two bottom loops. In this way, a quality connection comes out without unnecessary stress on the material.

For a beginner angler, it is enough to learn 2-3 reliable knots that can be used in different situations. However, with experience, you will need additional methods of attachment that allow you to approach tackle installation in a more professional manner. Each knot must be tightened evenly to avoid twisting. Also bindings knit, pre-wetting water, otherwise the line or cord can be damaged or simply tighten not all the way. Moisture helps the material to stick tighter, so dry mount the knot can not. Using glue that instantly sticks to the surface is an inexcusable mistake. Such a knot will tear on the first or second fishing trip and let you down at the most important moment.