Best 20 discount Gun Maintenance – Gun Smithing

Hey youtube nc shootist here did a video. A couple weeks back i think it was on. The Remington 760 game master disassemblies. And reassembly and i had a viewer comment hey why don’t you show us how the bolt of the 760 comes apart and goes. Back together so i figured i would show that process to you today so getting. Started what we’ll need a small hammer you might. Need a big hammer if your vote is stubborn like mine was the first time i. Took it apart a small little computer. Type screwdriver a one-eighth inch punch. It’s good to have a magnetic part straight just make sure nothing gets lost a pair of needle nose pliers and of. Course your bolt so let’s go ahead and. Get started and when we look at the bolt. You can see that there are two small pins there’s a smaller one on this side. And a larger one on the other side that. Hold the actual bolt into the carrier. Alright so if you look there are some. Channels cut into the bolt and we can. See that little pin that sticks through the bolt carrier into the bolt so first. Think we want to do is take our small computer screwdriver okay, and we’ll get. In there and push those pins up first. Okay and then we’ll take our needle nose pliers, and we’ll pull that smaller pin. Out go ahead and set it on our tray well. The pliers won’t let go of it okay now. We’ll move on to the bigger one on the other side you can see it here take out. Screwdriver again push that one up just. Enough to be able to grab it with the. Pliers okay. We’ll take that larger pen and set it aside and now the bolt will come free. From the carrier okay, so we’ll go ahead and set the our bolt aside all right now. I’m not going to take the extractor out because there’s a focus you can see. There’s a small pin in there that holds. The extractor plunger and i don’t have a. Punch that’s that size, so we’ll leave it. In there for now the only part left is. The firing pin okay and you can see focus alright you can. See there’s a small little pin that. Holds the firing pin in so the firing pin has a slot cut in it so what we’ll. Need to do is chuck this up in a vise. And I’ll show you how to drift this pin. Out so it’s its hard to do the first time but once you get the hang of it’s not too bad so let me get the vise. Set up, and then we’ll drift that pin out okay I’ve got our bolt carrier chucked. Into my vise and what I’ll do is use. Some softwood some pine or something. Leave the front lugs of the bolt carrier. Sticking out past the wood blocks. And then chuck where the pin goes. Through make sure that’s in contact with the wood blocks so you get a nice. Solid contact alright and I’ve already. Started this pin a little bit so we’ll just drift it the rest of the way out so. Take your punch. And just drift that pin out okay and it. Just dropped on the floor but no big deal well we’ll get it later all right. So what we’ll do is take the bolt. Carrier back out of the vise okay and. You can see once i take the firing pin. Out there’s that notch that lines up. With the hole in the bolt carrier all. Right so the reassembly process is. Just the reverse and one thing to. Mention before we get back to the reassembly you can see in my bolt. Carrier I’ve got a 760 and it’s the. Model a dl which has the chequered. The checkering cut into the stock and. The four in so the later Remington’s. Have a firing pin spring that sits down. In the bolt carrier okay if you’ve got. One of the earlier 760 s i believe they. Do not have a firing pin spring so. That’s one thing to notice if you open yours up and you’ve got an early model of 760 and it doesn’t have a firing pin. Spring that’s the way it’s supposed to. Be so don’t panic if you’ve got an. Early one and you don’t see a firing pin spring all right so let’s try to get. This guy back down in here okay we’ve. Got the firing pin spring back into. The bolt carrier and I’ve already started the pin that retains the. Firing pin and you’ll notice this is the. The top of the bolt carrier so the pin. When you drift it out you want to drift. It from top to bottom and when you put it back in you want to go bottom to top okay so it’s good to go ahead and get. That pin started you can see it there so. What we want to do is maybe back it out just a little bit. With a punch just enough to get the firing pin lined up okay go ahead and. Put your firing pin in and that notch. Will line up with the hole here let’s. See if we can get some daylight through here see if you can see that okay so you. Can see there’s that notch in the firing pin, so we’ll move it out of the way and. We’ll start our pin from the bottom okay and that will at least line everything. Up so we can get it set back in the bolt. Carrier okay so we’ll go back to our. Vise all right we’ll take our eighth. Inch punch. We’ll just drift that pin back in there. Okay so you can see that pin is now set. Back into the bolt carrier the firing. Pin is secure but it’s also free to. Move around that’s what you want you don’t want the firing pin to be stuck forward because if it is once you go to. Close the action you’re gonna have a slam fire and that’s what you don’t want so make sure you’re firing pins nice and free okay there’s the large hole. That was on the side of the carrier. And you’ll notice the actual bolt. You have two different size channels you’ve got a smaller one and a larger. One okay so obviously the larger one is. Gonna line up with the larger holes okay. So we take our pins that we set aside in. Our tray i will take the larger one. And we’ll get it started into the. Bolt carrier body okay we’ll line up the channel and. Just push it in with your thumb now if. You have trouble just take your punch and kind of give it an extra little push but it should go in pretty freely so if. It’s not going in freely don’t force it and try to figure out what’s causing it to bind up all right, so we take out. Smaller one just push it in with your. Thumb and there you have it there’s your. Disassembled and reassemble bolt for the. 760 game master so i appreciate you. Watching if this video was helpful give it a thumbs up thank you guys for watching god bless we’ll see you next time.

Make sure we’re going here fun to do a. Short video and piece of equipment i got. This week washing last sunday it’s saturday now. The following week I’ve been after one. Of these for a while i was gonna double myself which I’m talking about a gun. Stand or a workstation type thing to. Actually put my gun my rifles and while. I’m working on them and that was gonna build one but i wanted me to was gonna. Build it in such a way that they collapse and it was easily storable well. I got looking around on amazon and well. I looked on midway usa there first and i. Had the one that i wanted in the cart and hit pay now or whatever it was and. We’re sorry we don’t ship to canada of course you don’t but i happened to find. The exact same one that i was looking at on amazon that midway had and it’s a. Tipton Compaq range right i haven’t even. Opened the shit that i got last sunday and i mean have a look at it and i. Haven’t taken them in the package but. They obviously took it out of the package customs were ever have a look at it because they recanted even though. It’s a it’s a plastic press lock claim. Shelf yeah called the typical compact range. Weights i can tell you just by looking at it. It’s not a vise it’s a gun rest or a gun standard rest or no yeah it’s for. Holding your gun in place while you’re working on it’s got no moving parts other than the two or end arms and the. Base extends. It collapses to 11 and a quarter inches and fully expands to 17 and three-quarter and that’s pretty much all. It is its just a place to put your gun. And that’s all i wanted i don’t care about having pockets and little places. To put two i don’t need that kind of thing i just need something to hold my gun instead of using my sandbags to hold. My ankles they’re not effective they don’t hold the gun any guns worth a damn I’m. Just going to take it out and have a look at it and put a gun on it got to. Take a scope off one of my rifles off my cross man nitro venom desk as the scope. On it is a bsa black-powder scope which. I found out is exclusive to midway usa as well it was made for them and it. Supported 16 by 44 illuminated reticle. Mobot the radicals turned side was on. I’ve got to take it off i contacted bsa usa, and they told me to. Get in touch with blue dog 3pl here in. Ontario and i did and they told me to. Pack it up and ship it on back to them, and they’ll replace the scope with. Whatever they have that’s close to it available because that scope is no longer main so hopefully I’ll get. Something happy snow for free because it. Is true it’s under warranty anyway let’s. Get into this here. Talk on the radio. I don’t know how close i am i really. I moved the camera back a bit. That’s writer too close okay I’ll just. Keep the case and I’m wl just pull back. And I’ll just hang it up somewhere it’s. Pretty heavy for what it is its six. Rubber feet on the bottom. Well plastic all of it. Pretty solid pretty sturdy pretty hard. Plastic yeah i like it down. Why is that month snap down not this one. It’s supposed to be i don’t want to say. It’s cheap because it doesn’t feel cheap i think it’s a it’s its made of a hard. Durable plastic rubber rubberized. Whatever you want to call them places. The gun sits in it works. Stop always in the way. No way. No solid. This. Paper down here with my kids. At the snow think you said the schools gotta take it off and send it back. Pretty good spoke to well it was until the radical turn sideways it’s an air. Gun rated springer magnum springer scope as well yeah this is meant for it’s just. That right there just holding the gun. I’m happy of course in it being bought. In canada wasn’t as cheap as it was buying him from the us either i think it. Was $17.34 us and i think it was like. Three bucks to ship it to me amazon it was thirty-eight ninety-nine but i still got free shipping and. Everything out of it because being a prime member do not an amazon prime. Member if you shop on amazon it’s nine. Dollars a month via to be a prime member and everything you order is free. Shipping and i think that’s worth it. Plus with the advent of the prime video. That they have on there you get to watch stop for free as well which is movies and tv shows and everything it’s actually i think it’s worth the money a couple on top of Netflix that we have. And we’re governor a lot of our bases cover them and stuff we want a lot. Yeah so that’s the tip the gun advice range friendship or whatever you want to call a compact range faces i think this. Is the lowest model they make because i dunno they make big ones that. Have all your spaces to put tools. And other stuff pain it’s a proper. Workstation oh by the way don’t mind my Denise in the background here I’ve got a load in the washer here helping to. Birth of one so i make a video and do a little laundry too yep that’s the range. Right compact range right they keep forgetting the name of it. That’s cool. Gotta remember how the gun goes in here now. I’ll put them maybe I’ll put a little. Dot or something to let me know about that’s this side well i guess it doesn’t. Matter I’ll take the steering turning. The gun around. Well i got this microbiome desk up here. I love the look of it i love that the fact that it’s all black i love the. Stock on it’s a really comfortable stock i was taking about camo in the. Stock takes the recoil pad off and leave. It blacks but i have camel guns before. And they come out really good really. Good. got all the paint down there’s orange black or contractor flat black forest. Green i think i got a brown or a tan. You just spray all the colors randomly. And then i take a cedar branch and just. Place it against them with the black and just go over with a black that way that the color underneath comes through and. It’s gets the pattern gets painted over with the black it’s cool works really good by the way i think that’ll end this. Video for the tipton’s compact range. Vise because it’s not a way so it’s just. A gun station holder there’s nothing in here that clamps hanging down at all it just sits in their ok see you later.

Hey guys this is chris with i want that. Reviews today we’re gonna be taking a. Look at a new tool that’s available from gerber called the gerber short stack now. This guy has a manufacturer’s suggested. Retail price of $54 and you can find it. For less than that on amazon i believe. The lowest i saw it was about 32 buts. It’s comprised of three different plates. That are all held together with earth magnets and a rubber bit driver holder. You have these three plates that are. Held together with magnets it can be a. Little sticky and tricky to get apart. But essentially what you’ve got here is. Multiple different tools that can be used for the ar platform and each one of. These will interface here so that you can get a grip onto the tool and use. Then for the different things and then once you’re done you grab the whole the. While setup again put it back together. Such. Put your piece back down in here and one. Of the coolest features about this guy is it is magpul moe and my ad compatible. So you just take this guy slip it down. In their snap it shut you’re good to go. It might make a little noise but if you. Got a rattling around but i keep a couple other things in their normally so. So i don’t usually get any sound. From that and the caption over there we’re not gonna worry about that right now initial impressions when i pulled this out of the box it was i was very impressed I’ve had my eye on this since i first saw their marketing for it they first started talking about it and I’ve. Been I’ve been trying hard to get a hold of it just got a hold of one here. Actually my wife bought it for me for Christmas and I’m very impressed with it’s a. It’s a pretty solid little tool the. Drivers at that it comes with as a phillips and a torx head that torques. Will fit your if you have anti wok pins. It will fit my magpul bad lever it’ll. Fit several things the it as well. Happens to be the same size or roughly. The same size as the bolts for your. Accessories on your rails the problem with that is because it is a torx head. It is a little smaller than i would not recommend using it for these i tried tightening one of these down and it off. The edges on it just a little bit so. I need to see about ordering a new one from looking at likes i love the compact. Design i love the fact that you know it breaks down and it’s got so many different tools it’s its just it’s a very well-thought-out tool that you know. Just snaps together and you know. You throw in your gun and you’ve got most of the tools that you need for you. No on-the-fly maintenance i love the fact that this guy fits in the grip and take it with you i love the amount of tools it’s got tons of tools on it tons of different things that you’re gonna be able to use that are gonna be practical and useful for just about. Anybody that’s gonna run an ar and i really like the design you know gerber obviously spent a little bit of time on this getting it all you. No thought-out and you know putting it all together so that it worked so that it was practical so that it was functional and that shows as far as. Dislikes I’m a bit unhappy with. With the fact that this bit rounded. Off i can’t help but feel like that’s a. Little that’s kind of my fault though for using it in something that. Was not torques so you know that’s you know that’s on me the other thing though that i noticed was here a couple days ago i just. Wanted to kind of take a look and see how it worked with the 3/4 inch i. Was swapping out a flash hider and it. Rounded it skipped across the threads. Are not the threads that skipped across the machining on this here it was. Actually this this muzzle device here and you can see a couple lines. Here from where i was working on it and. I just peeled right off the edge so I’m. Not sure if this is just a little bit out of spec or if it just you know. Happens to be that particular flash hider but i would say not obviously not. To rely on this as the your only tool if you’ve got an armorer’s wrench or if you’ve got a crescent wrench that can handle a flash hider i would say to. Absolutely do that this is great for you know on the fly if you’ve got to change something on the field and you and you need to work on it’s fantastic but i wouldn’t say that it’s something to rely on those are really my only two. Dislikes um i would think that. Would be something like i said that was partially my fault and and probably. Primarily my fault but those two issues. Are gonna get me to knock this down just. A little bit in my opinion of it i still love the tool. It’s still gonna go everywhere i go it’s gonna go into my grip and it’s gonna stay there but overall I’m gonna. Give this guy four and a half out of five stars it’s gonna lose that half a star there because of the rounded bit and the issue with the. 3/4 inch wrench being a little out of. Out of whack but those were minor issues. This is a fantastic tool it is worth every penny and i would recommend anybody take a look at it and see if it’s something that you’re interested in I’ll go ahead and include a link to their website in the link below as well as their facebook page as always thanks so much for watching if it weren’t for you guys i wouldn’t be here please do like subscribe and share and keep checking back on a weekly basis for more reviews of awesome products just like this one that’ll make you say i want that.

The real avid gun tool pro is loaded. With 30 gun maintenance tools in one compact package no matter the make or model of your gun optics or accessories. The gun tool pros 14 driver bits will handle any screw you’ll encounter and the quarter inch bit wrench provides. Torque to handle the most stubborn customers there is even a removable. Magnetic storage container to keep parts and pins from disappearing installing or. Adjusting optics removing stuck choke tubes of any gauge punching or replacing pins smoothing burrs the gun tool pro. Provides the precise mission built tool for these jobs and more the real avid. Gun tool pro this is the gun tool your. Daddy wishes he had. You.

In today’s tabletop review I’m going to. Be taking a look at another ar-15 tool. This particular item is made by real. Avoid it is their gun tool pro ar-15 so. This one is specific to the ar-15 now. Real aven’t has got at least four or. Five different tools like this available. Some are generic that are designed to work on most firearms including pistols. And rifles some are real basic and some. Are more like a four like a multi-tool. Type of device this one is the only one. That they have which is specific for the ar-15 so that’s why I’m reviewing that what I’m gonna do is we’re going to talk. About the packaging talk about the tool talk about the specs I’m going to open it, and then we’re going to see how well the tools that are included with this device apply for the. Ar-15 so before i get into reading the. Specifications this particular tool is not inexpensive this runs for right. Around 50 dollars so give or take a few. Dollars and you get it in this plastic p. O p type of packaging and it also comes. With a flat dark earth sheath for the. Tool or they i believe this is molly. Compatible it says it’s molly compatible. I won’t know until i open it this has not been opened and this is the first time I’ve I’ve seen one of these specific tools so if i stumble along the. Way, please let me apologize ahead of time because i. Will be looking at this for the first time right along with you now according. To real avoid this has 35 different tools in it and. We’ll get into that shortly well i hate. This packaging here these are this packaging is just a real pain to. Open up and get your items out and if you’re not careful you can cut yourself severely with this plastic which I’ve done numerous times in the past so let’s. Just look at the packaging let’s see. What do we say what does it say advanced multi-tool for the ar-15 platform easy. And efficient tear down carbon scraping maintenance and reassembly mounts and customizes scopes and accessories so the. Back the back gives us a breakdown of. The different types of tools that we can. See we get with this item and I’ll read. I’ll read that a little bit more once i get it unpack aged and will come back and I’ll read that so what I’m gonna do. Now is I’m gonna go ahead and get this opened, and we’ll take a look take a look. At what the tool looks like okay i think. The only thing worse than opening that packaging would be having to watch somebody else open that packaging five. Minutes struggling with that not not my. Favorite type of packaging but so inside. The package is the tool the case and. There are some instructions on how to. Utilize the tools which i won’t bore you. With all the details on that but we are. Going to talk about all the specifics they come with this. Let’s start out with the ballistic case. It is molly compatible that’s good you can definitely put this. On your vest or on your backpack or on a. Belt i don’t know what this is made out. Of specifically but we have a nice snap. Right here. Some sort of soft material on the inside. The stitching appears to be adequate for. This type of case on the side is a. Small velcro compartment and this is. Where the site adjustment tool lives and. This is obviously one of the items that’s included with this particular tool so you’ve got a site adjustment. Tool with five pins on it and then you. Have a site adjustment tool with four pins on it so that should pretty much cover the a1 through the a3 type of. Front sights so the case is good the. Front sight tool appears to be well-made. Form of what i can see it has a knurled. Raised surface on either end so if. You’re holding it like this it’s not gonna slip around in your fingers it’s. Got a good weight to it so I’m not. Sure what material it’s made out of but it feels pretty solid now the tool. Itself the tool itself is actually. Pretty heavy there’s there’s some. Definitely there’s some weight here the weight is definitely going to be. Beneficial for one reason this is a. Strike panel right here this textured area this is designed for you to pound on things as with any hammer. You’ve got to have some weight to it to be an effective hammer so the bulk. That this tool has is going to make this. Striking surface a fairly decent emergency hammer the fit. And finish of it this black area here is. A rubberized material this area appears. To be plastic so and this rubberized. Material does have a some texturing to it so it does appear to be a good gripping surface this compartment back. Here appears to be plastic it is hinged. And the hinge appears to be. Spring-loaded so if i pull it up you. Now it goes up and it’s not going to flop down on you so until you go and. Push it you need to get a little bit of force on it and then it’ll snap into. Place so this is a good design right. Here this isn’t gonna flop around it is gonna open up on you and your bits. Are not going to fly out as you can see. In this particular compartment right here we’ve got five we actually have. Four bits and we have a punch tool and. These if you can hear they’re held. There’re magnets in the bottom of this compartment that hold these bits in so. The bits are not really gonna fly out. And you can see they’re not moving and. They’re double-ended bits so this particular one we’ve got two flat heads. This particular one appears to have in a. Allen a 3/16 allen and a phillips number. On this is a pin punch and it doesn’t. List a size, and we’ll have to talk about that this is a 3/32 and a 764 allen. And a 1/8 and 9/64 allen and all of. These bits appear to have some sort of oil on them protective oil so for now I’ll just put. These back in, and we’ll revisit these shortly and so this is very well. Designed from what i can see and of. Course we’ve we’ve got our bit retention. Which is good the upper part of this now. These tools come well there’s one other. Tool where there’s a that includes a. Flashlight this is not the one that includes a flashlight the ar specific tool includes a little box that slides. Out and there’s a little tab on the. Bottom that you push up on and it will. Open up and my understanding is that. That it is magnetic for holding pins and. Springs and such parts that you might be working on at the moment or maybe you. Want to carry around some spare parts with you so what we’re gonna do is we’re. Gonna test that I’ve got a roll pin it. Is magnetics and we have a take down. Spring so it is magnetic you can see. That the parts are staying in place right there so the magnet is nice if. You go to open this the parts aren’t. Going to pop out on you and they’re not going to rattle around as well so. Excellent idea you know as i understand. It that magnet is strong enough to hold. This in place not only does it slide in. I can feel the magnet grabbing. Hold of this metal plate right here there’s obviously a little piece of metal underneath this plastic. So it’s pressure fit right there as well. As having a magnet so double safety i. Don’t think this is going to accidentally fall out doesn’t definitely. Move around from what i can see so. That’s good as well i think the idea. Of the storage compartment to me is. Better than having a miniature led. Flashlight which may or may not be very good so the storage compartment i think. Is a great idea the strike hammer i. Think is a great idea if you need to. Well let’s say you need to pull your trigger out and you’re out in the field you’ve got the pin punch and you’ve got. This striking surface here so that’s. Good the bits you’ve got a bit driver. Here and you have a bit driver here so you have two bit drivers they’re both magnetic they’re not ratcheting so. That’s the only thing i would say is kind of bummer is it would be nice if. The if one of these at least was ratcheting not a deal breaker by any. Means that’s that’s just kind of like a wish list but you’ve got two of them so. If if you’ve got something. Stubborn and you need a little bit more torque on it go this route might be. Better than going this route so you’ve got actually two points you can use for your bits now the inner components here. They don’t all see these have a. Firm they pop up, but they’re not locked into place. And let’s see we’ve got this knife which. Feels pretty sharp now this knife locks into place right. Here and to release it we just push down. To release that so the knife itself has. Got it’s got a I’m sure I’m drawing a. Blank for this it’s its it’s got a surface right here and then of course. It’s curved they call this a raptor claw point. Utility knife we’ll talk about that a. Little bit more back here excuse me. While i take this off a camera i can’t. Seem to grab ahold of whatever it is. This particular tool right here pops up. Now this one locks in place as well. This. After pause with I’ve deposited just a. Second I’m I’m looking at the diagram of this particular tool and it shows this. Item right here and it says lanyard loop bolt override the lanyard loop it’s. Pointing at a little hole right here which isn’t present on this particular tool we’ll talk about this in a little. But but this one does lock into place as. Well flipping this over to the other side. This tool locks into place and this is a. Bolt carrier scraper and a fine metal. File and it’s not much of a filing. Surface I’m not I’m rubbing my finger on it’s not it’s not even really not. That i have any fingernails but it’s not really enough to even file down my. Fingernails so the bolt scraper we’ll. Talk about that shortly as well I’m I’m a little dubious on how much functionality that would be for an. Actual fine metal file i don’t think. That’s gonna file anything if it won’t file my fingernail I’m not gonna count. On that being a usable file for filing. Small parts. Other tool which locks into place is a. Nine function bolt carrier group scraper and cotter pin puller, and we’ll talk. About that as well this particular part of this ar-15. Multi-tool is very similar to another real avid product that they sell you can. See right here this is a this is there. Ar-15 scraper tool and i’ve done a review. On this before and i really like this. Tool it works it does its job very well and you can see it’s pretty much. Identical it’s just one is silver and one is black and it does also lock into. Place and the three torques is that are. Here we’ve got a t20 a t 15 and a t10. And like i mentioned those do not lock. Into place this particular item is a. 1/32 threaded post and it is threaded. Right there I’m not sure exactly what. That’s used for I’m thinking that you might be able to. Thread in a wire brush or something for. Cleaning we’ll have to investigate that. A little bit more as i read the instructions that came with the tool which i have not quite done just yet so. Going back to the compartment here let’s take one of them fits out yeah those. Bits are not gonna fall out on you nothing i hate worse than a bit screwdriver and you go like this and the. But just falls out i absolutely despise those types of. Tools this with the magnet it’s gonna. Hold your bit in there it’s not gonna fall out on you and you have a magnet. There as well and it’s not gonna fall. Out so that’s good all right um so far i. Like everything i see about this tool i think real habit put a great deal of. Thought into this tool they’ve added some safety features the inclusion of. Magnets to hold the bits into place the magnets to hold your spare parts and hold this little storage compartment in place the hinged spring-loaded assembly. For these bits the magnet retention for. The bits everything that i would put. Into a tool if i was designing so great. So far now let’s move on and actually. Talk about the some of the features I’ll. Go through the actual included instructions here we won’t spend a whole. Lot of time reading that but i wanna i want to actually go over each individual tool and talk about how real avid sees. The tool being utilized so the knife. Raptor claw point blade it’s designed. For utility cutting so opening apple. Boxes cutting rope trimming cleaning. Patches and it mentions to resharpen the. Blade with a carvey carbide or ceramic. Sharpener following the sharpener manufacturer’s instructions okay. The blade is very sharp you’re. Not going to have to sharpen this as you get it I’m not sure of how useful. This type of curved point blade would be i do not have a lot of experience. With these curved type blades a standard. Drop point would be my preference for. This blade i just I’m not exactly sure. You know this looks more like a box cutter and that might be more in line. With their intended purpose of opening up ammunition boxes so I’m sure there’s some logic to having the curved blade on here i would probably prefer a drop point. Myself but you know we’ll see because. I’m definitely going to keep this particular tool in my range bag and. Hopefully it’ll see some use down the road. The bolt override tool where did it go. Down at the bottom again. So i have to take it off camera i don’t have a the bolt override tool. The bolt override tool can be used to. Clear jammed cartridges it gets stuck between the bolt carrier group and the charging handle carefully engage the. Firearm safety remove the magazine pull the bolt carrier group back using the tool and shake the stuck cartridge out. Of the firing firearm. They do not show in the diagram here. This in use so I’m assuming that it. Would be used i don’t know how actually. This kind of gives me the impression you. Would use this to grab a hold of the bolt and pull it so well I’ll have to. Take a look at that particular tool if. That is indeed its intended purpose. Having it locks in place is definitely a good idea the let’s see the pin punch. Since they didn’t list what size that pin punch is there’s nothing written on. It their instructions don’t say anything either when we get to that to the next stage of this video where I’m actually trying to see how these tools fit to an ar-15 well. I’ll see if i can come up with what pin. Pin or pins on the ar-15 that punch will. Be applicable for right now i don’t know. So I’ll need to have that I’ll need to have an ar lower in front of me let’s. See the we’ve pretty much talked about. This little compartment they as well. Mentioned that the magnet could be aided for picking up small parts so if you. Have problems picking up little small items you can use the strong magnet. That’s inside of this I’ll just go ahead. And pick up the parts. And other than that we pretty much. Talked about the are the functionality. This box already i like it is plastic. With the magnets so hopefully what I’m. What I’m afraid of as you can see this box is plastic and this top is plastic the little hinge. Right there is a plastic hinge and unfortunately a lot of times with these. Types of components after repeated use of this happening these shear off so i. Hope that doesn’t happen with this. That’s the only thing i would really be. Worried about with this little compartment is that hinge shearing off. The let’s see the bits going back to the. Bits right here. They really don’t say much we’ve talked about the sizes of the bits are ready. And flipping over the instructions over. Here to the other side the other side basically discusses using the tools for. Cleaning your bolt and then this front. Sight a gesture this does have a limited. 3-year warranty on it and that’s pretty. Much yet so well pretty much the rest of. The instructions here show the bolt. Scraper tool and how to use a bolt. Scraper tool for scraping the inside of. Your carrier cleaning the bolt face. Cleaning the firing pin there’s another. Specific tool for cleaning the outside. Of the bolt tail of your bolt and the. Bolt waste and then between the locking lugs and scraping behind the lip of the. Cartridge extractor the 1/32 threaded. Post I’m still fuzzy on what that’s. Specifically for and I’m just double. Checking my notes yeah i have no. Information on what that specifically is designed to be used for so let’s move. On to the next phase here I’ve got one. Of my rifles here and what I’m going to. Do is just we’re gonna take a look at. The tools and the specific sizes. That come with this to see how. Applicable they are to an ar-15. Okay i have an ar-15 lower receiver here. And we’re going to take a look at some. Of the tools and see how well they fit. With this particular ar-15 lower so you. No i have magpul bad lever here we’ve. Got the kns anti-roll pins so those have torques on it we have torques here we’ve. Got a magpul asap qd plate with their. Sling attachment point and there’s an. Allen bolt that holds that into place as. Well we have a roll pin here roll pin. Here on this side that will we’ll take a. Look at so since we’ve got two smaller. Torques right here let’s take a look at. Our complement of torx tools and see. What if any of them will fit so the. First one here. Now they’re not all individually labeled. The Smallest want to be a t10 okay no joy in. The t-ten the t10 does fit the kns does. Not fit the bad lever i need something smaller to do the bad. Lever let’s jump up to the t 15 see if. The t 15 that’s actually not a torx over. Here on the magpul asap qd plate that. Needs him hex key or an allen key and we. Have a 3/16 which is too big and a 9/64. And there we go, so we’ve we’ve got that. Covered as well we only have a couple of. Roll pins on this side the roll pin. Punch which is included in the tool. I could use that to punch out the roll. Pin holding the trigger guard on it’s a. Little bit smaller but it i wouldn’t. Consider it ideal for that purpose but it could be used for that the roll pin. Over here looks like it’s probably too. Big for that particular roll pin let’s. Flip the lower over we also have a odin. Works extended magazine release here and. Those take allen bolts as well and it. Looks like the 332nd that comes with the tool would handle that as well. Let’s see there is a hex bolt that holds. The grip on but pretty much guarantee. You that this tool is not going to be suitable for removing that because it. Just it’s not gonna be long enough and there’s no extension included so there’s. No point in even trying that that pretty. Much covers everything that’s on this. Particular lower receiver over to the. Upper receiver take a look at an upper receiver and what can we do on this. Upper receiver well we have the primary. Arms md ad red dot this is attached to. The upper receiver with hex bolts as. Well these are larger hex bolts let’s. See if we’ve got that’s too big too. Small bingo so the 9/64 covers those. Bolts on this upper the hand guard itself. Which is centurion arms there’s four. Bolts back here and two bolts up front that hold this on see if we’ve got what. We need to take this hand guard off we do. The 9/64 works for that and the other. Bolt which is underneath these rail candles all have to their’s a smaller. Hex bolt underneath these rail panels. I’ll have to do that a little later. We’ve got the magpul. Xtm hand stop here and that has a hex. Bolt it would appear to be a hex bolt it. Could be a torx know if it’s a hex and. The 1/8 handles that that pretty much is. All of the bolts and roll pins that i. Have easily accessible that we can look at for the purpose of this given that i. Would say that the included bits were. Well thought out and real avid included. The most common bit sizes that are used. In accessories and ar-15 lower receivers. I think we only ran into one that i. Didn’t one bolt that i didn’t have a bit. For so that’s great, and we didn’t even. Look at any of the flat heads because i. Don’t have any flat heads on this particular a ar-15 but so far so good. The one other thing we could test we. Could take a look at the sight post tool. Since this particular upper has a standard f marked front sight on it and. This requires a for post. Adjustment tool. Yeah I’m not gonna adjust it because i. Already have this sighted in but this. This tool would work just fine for making adjustments here i don’t see any. Issues at all at least the four-post. Works good there is a five post on there. I don’t have anything it uses a five post front sight so i can’t test that. Now as for the last part of this. Video i wanted to go over the bolt. Scraper tool and how it applies how you. Can apply it to cleaning your ar-15 bolt. And bolt carrier now the little hook. Right there we can use that hook to. Remove our pin. Let’s remove our firing pin. Like so and then remove our bolt. Okay um I’ll try and speed this up so it. Doesn’t stay get too incredibly boring. Now our bolt scraper is basically. Designed to go in and clean the inside. Of your carrier like so this is this. Bolt is or this carrier is clean so I’m. Just going to kind of demonstrate the different tool functionality here a little bit and we’ll just go through the. Different functions this particular area. Right here is used for scraping the bolt. Face like so now i have used the other. Tool quite extensively for cleaning bolts in the carriers, and they do work. As advertised the firing pin the smaller. Smaller diameter front part of the firing pin we would use this area right. Here and clean it like so and then you. Have a larger area a larger cutout right there which is designed for this. This piece right here goes in like that. And you rotate your bolt and you can see. The curvature right here lines right up. With the bolt tail and the shoulder the. Bull tail and you basically just turn this and all of that carbon build up. Will be scraped right off now the. Waste of the bolt right here you’ve got. This area right here you can use this. Tool for cleaning inside there and for. Cleaning in between the lugs on your bolt you can see that that tool fits. Perfectly in there so when you get carbon buildup you go in there and scrape that and that works out real good. And the this tip that i use to pull out. That retaining pin you can use that for. Getting down in here in cleaning around your cartridge extractor or excuse me. The cartridge extractor which is down. Here not the ejector so there’s a little. Lip right there and you can use this to get down behind it and scrape any crud. Or any carbon buildup like so the i. Think that’s everything i wanted to test. And demonstrate in this video again i. Think this is a well block tool in the. Fifty dollar range it’s i don’t find any. Fault with the tool the included bits. Are appropriate for working on the air. 15 the cleaning tool is an excellent. Tool the quality the construction is. Great and the ballistic nylon case and. That’s pretty good as well so that’s a nice bonus to store your tool so i have. To give it two thumbs up and I’m going. To end this review tabletop review as. Well as a functional demonstration of. The of the real avid gun tool pro for. The ar-15.

Hey guys will air 1,500 calm got another. Unboxing video for you today we’re. Looking at a product from real avid if you’re not familiar with real avid they make a wide range of different cleaning products for guns as well as tools this. Here is the gun tool pro ar-15 they as well. Have a gun tool pro which is a more of a. Multi-platform tool or general purpose tool this one here is made specifically. For use with the air 15 platforms they’ve designed this so you can have a tool on. Your person that has just about everything you need for a field repair. Or for stripping down the rifle and doing some cleaning out in the field so. We’re gonna take a look at it today retail packaging open it up we’ve got. The gun tool and a nice little pouch and. I believe we got some instructions in. Here yep throw that box off to the side. See what we got okay so here is a pamphlet it’s gonna. Have the this is the user guide and warranty information just you know goes over all the different pieces of the. Tool on the back you’ve got user guide. Some information about the air front sight tool safety and care and. Maintenance of course warranty information which this unit has a three. Year warranty from the data purchase and. There’s also a little pamphlet in here. That shows some of their other products they’ve got a air 15 maintenance kit which is like a cleaning kit with all your different brushes it’s got a looks like an ap brush in their different types of things bolt scraping tool then. You’ve got they have a plier style air. 15 tool it’s similar to the air to the. Gun tool pro air 15 doesn’t have quite as many tools on it and it’s more of a like leatherman style tool there’s the. Original gun tool pro they’ve got. Some other universal cleaning kits etc so taking a look at the gun tool pro air. 15 comes in this nice tan flat dark. Earth ish pouch it is molly compatible. So you can throw that right on your pack on the side here we’ve got this little compartment here and this is holding the. Ar front sight tool if you don’t have one of these they’re awesome. I’ve been using for years a the tip of. An m855 projectile to make elevation. Adjustments to the front sight these tools are a lot handier a lot makes it a lot easier to push down in that front. Sight post and make your adjustments this is compatible with a two and the eighth one front sight assemblies very. Cool tool to have it’s a lot better than using the tip of a bullet and again i. Use a tip the tip of an m a 5/5 because the steel core penetrator in there you. Now it’s hard enough to allow me to push the detent down and rotate the front sight if you use something like m 183 just a 55 grain ball it doesn’t work. As well but now you don’t need to with. The real avid front sight tool go ahead look at the main unit here it out okays. Appears to be very hefty very well. Made looks like it’s pretty stout little unit right here this is one of. The cool features this is the tap hammer this is a hard surface they put on here and because of the tool has a good. Amount of weight to it you can use this for you know i wouldn’t we use it in place of a hammer but if you need to tap on something or need to drive out a d-10. Or something you might have enough inertia and weight here to tap that. Out with a with the tool pretty cool another thing i like on it has two. Quarter inch bit drivers you’ve got the. Main one here this is a solid fixed unit, and then we have one here on the side and i believe on the back if you lift. This door open it’s a spring-loaded door we have various different bits in here. You’ve got allen bits you got flathead phillips, and they can go either in the front which is a solid unit and i believe yep in this one here — there’s. No ratcheting action on it’s just a solid fixed-fixed but there or excuse me. Driver but that’s pretty nice you can get on the side if you need to get more torque or if you’re just screwing something in you can get the front there like i said you’ve got several two different sizes of phillips. Flathead looks like four different allen. Heads so pretty cool oh this is another. Cool feature that they showed us at short. Show when we first saw this product pop. This off it just slides down it is frightening held in their by friction this is a little compartment that is it. Over here magnetic i don’t know if you can see that magnet symbol there but. This is a cool little feature so when you’re working on a gun if weather out in the field or even here on the bench if let’s say you’re gonna you know you have to remove the grip for some reason and you’ve got you know say a detent in a spring you know these little things can fly around that you can easily lose them well this little thing is this little compartment is magnetic so you. Just drop them in there it holds them. Down nice and secure you can store them in there and just a nice little handy. Place to keep your different excuse. Me your different little springs d tensor roll pens things like that pretty. Cool you just slide it back in and it slides in there and again it’s friction held but it’s pretty secure some. Of the other uh tools on here you’ve got. Like a almost swiss army knife style assembly here this here is the nine. Function bolt scraping tool so this is. Made to scrape the bolt in different areas on the carrier and this does lock into place this is locking in then. You’ve got a release right here on the side here we got the torx bits ranging. From size 10 through 20 i think it’s 10 15 and 20 these do not lock they just. Fold out they have two different positions that there’s a little detent in there that kind of holds it you either have straight out like this you can get you know get on there or if you need to get an additional torque you can turn it here it locks in place and then. You can put additional torque on you know scope rings or whatever you may be working on got a blade here this is just. A utility knife and then this is the. Carrier scraper this one locks into place as well nice and firm has a little. File here on the end but this is what you use to clean the inside of a the carrier when you pull the bolt out it’s an area that on bulkhead group on an ar that gets you. Now a lot of crud in there so this is a really handy feature that in the benign. Function bowl scraper and a little magnetic compartment here really you. Now drew me to this multi-tool so. We’re gonna take this and do a full. Review on it we’ll have you know up-close detailed pictures on our website and I’m also going to do a video. Of me cleaning a bolt carrier group that. I have in one of my rifles that has had a couple thousand rounds shot through it without any major cleaning I’ve simply. Pulled the bolt carrier group out I’ve wiped it down and really brocaded it and run it and it is filthy, so we’re gonna. Put the gun tool pro ar-15 to the test. Cleaning that bolt I’ll get that on video and then I’ll let. You know what we think of it stay tuned. You.

This is chris from all guns 101 with. Another unboxing of the captain best gun. Vise sorry for the angle the camera i. Don’t really have much room to mount it and i need to get him out for the camera so let’s open it up so right i have here. Is tipped investment advice most. Versatile gun vise available it also has. Some of the best reviews for gun vices so let’s see what you get when you open her up slide that down so right away the. Base i presume i have not opened this so. I don’t know whether it contains an arrow what’s inside let me just turn it. Over this way hopefully what we have. Here let’s turn it this way to the. Camera written tipton best gun vise. Feels to be plastic probably injection. Molded surprising has the patent. Information on it btw i brands calm. Slash patents seems to be some phillips. With some bolts in the back holding on an aluminum rail which i presume that along the rail is for these slides and. Different rocketry let’s just put that. Down here for the moment what is that. Box up there here we have one of these. Saddles looks. And empty box so let’s move that out of. The way once again feels to be almost. Like a rubber feel here we have there is. Right right left right same system. Molded plastic with which i presume is. Four bolts let’s just put that on here. I’m gonna move this out of the way for now mystery box. Two to three snap cap that’s what i have available seems to be all your. Adjustable plastic oh that is identical. Molded one like the injection here will. Be your clamps camera here we have. Wheels screws how you want to call them. That these two that’s probably more than night before your rail able to slide. Them over and freely and that would be. Another saddle as i would say you have. Your middle as i would call it which is. For your ar pistols and everything else. And instruction manual so what i’m going. To do is uh i’m gonna get all the t. Bolts in i’m gonna get this thing set up. I’m gonna throw a gun on it i’ll let you guys see what it looks like and how secure it is so stay tuned for a little. Bit more that we’re back and the tipton’s best gun base is fully assembled let’s see how it mounts with a. Gun what i’ve noticed is depending on. Where you put your front guide as i’ll call it you do lose. Some of your trays here same on this. Side so you do lose some storage space it’s not the end of the world to be honest you still have lots of room on. Here and if you don’t well you always just get a gun map work you know a bit. More cable space as i’d like to say so. Let me just grab my clicker ruger here write it up today bush for coyotes so. Let’s set this up here let’s settle it. If you don’t know i’ve already made some adjustments to it just to see and it. Looks like i’m applying a little too much pressure so i’m just gonna sit. These back because i don’t like the amount of flex i’m getting and i’m gonna. Raise these up a little bit just that. They see that we’re a bit on the low. Side so loosen your side caps here. Basically i’m at the maximum height so. Let’s bring that to the max i’m gonna. Close these down and from this point on i’m gonna actually tighten just to try to get it even i don’t like the amount. Of flex that i’m getting on the back end here now if you’ve seen my video as i. Tightened there it is you see it in the. Video but everything is kind of going. Out of whack and since this isn’t the. Stock stock. I might have to remove let’s try this. Center here which is our ar piece loosen. This back up and for anyone who owns. Even ruger we all know this is a front heavy gun so let me set this down as. Much as i can same with this part here. Maybe it’s a low lowest degradation i. Just wanna see that’s fun if it still. Patches and that’s that that’s one issue i’m seeing right here is that this on. Certain guns you have to remove completely because it will not fit but. Luckily i found a new home fourth the. Cap that is perfectly circular hole so. It’s going to go in there and this will sit on the workbench until i do need it. For ag guns but sorry about that. So now let’s lower this once again to. Its lowest point tighten this one back. Up and we’ll do the same on the left side i’m gonna lock that down you want. To try to apply even pressure on it you. Don’t do anything crazy but now we’re secured and yeah i’ll say that’s that’s. Gonna decent job of holding that. Mobility wise if i really need to push. Hard i’m gonna move everything but. Before i move this so as we see it’s. Fully mounted this sturdy i’m not gonna. Lie it is a very sturdy setup but i. Would have liked to have seen some different things and different aspects to it just for the price that we’re all paying for this good gun vices don’t. Come easy and they don’t come cheap we all know that i’m just gonna level it out and like i’m saying for the price. That we all know it’s worth you can get. Some other ones out there yes they’ll be a little bit cheaper but at the same. Time more dependent on your needs because that’s where it comes out to fnd not at the needs that you think you have it’s at means you actually do have i clean a lot. Of guns and i’m fed up cleaning my guns on the floor or just on a table like. This with a mat so i think this will make my life much easier and it should. Make the overall long term easier. Especially on bobby because working from lower bent-over positions is not good on your posture or anything else so please stay tuned for more videos and more information as it will come.

I’m john mccoy with 85 41 tactical and. We’re here today to give you a short review of the tifton best gun vise you. Guys have seen this vise before on some. Of our product reviews and also on mail. Call mondays every now and again it is. Actually a really useful tool in our shop here now the tipton’s best gun vice. Can be adjusted to an extremely wide variety of firearms i really can’t think. Of any a shoulder-fired rifle that you. Really can’t fit this thing to starting. At the front here everything uses these. Big knobs to adjust and tighten down so. It’s all to listen adjust very fast we. Have the front cradle up here for the four end of your rifle or shotgun and you can undo this front knob and slide. It forward or back to wherever you need additionally you can undo this knob. Right here on the cradle and you can slide it up or down at an angle and. There are some detents in there that it skips over and you can set through a. Pretty wide range got to loosen it up a. Little bit more you can slide it through a pretty large range and get this thing. Really set wherever you need it when you get it where you want it and you lock the knob down there are little detents in here that keep it from sliding once. You lock it down so you don’t really have to crank it down hard but you can. Get it set in and you’re pretty good to go on the back here this is the portion. That really gives it the vice name now there are two knobs that allow you loosen this up and slide this portion forward or back on the aluminum track in. The base and once you get it set to where you want the buttstock to be you have two cams here on either side they. Have these big locking flipper levers on. Them what you do is initially you start with the levers in the up position and you use these black knobs on either side. To adjust the pads to get them fairly. Close to the stock you then flip these levers down and it cams those pads in. And applies pressure to your stock and it really locks it in there i mean you can see i can lift the back of the i sat by it so it’s really holding the stock in fairly sturdy and because these. Are just in and out if you’re working with a really fine wood stock and you don’t want to worry about mari you can use pretty light tension if you’re. Working with the tactical rifle that’s got some weight to it or you’re really going to be doing something that’s going to be moving the rifle around you can increase the tension and really crank that down additionally there is padded. Material in the middle here to protect your stock if you’ve got a really good angle on that stock on the toe then it’s. Not going to get nicked up or torn up now one of the really neat features of. This vise is it was designed to allow. You to work on ars as well very easily. Now you see we have an ar-15 in here and one of the primary ways to clean an. Ar-15 is to shotgun the rifle open that. Way you can just slide in your bore guide you can run your rods in etc and. You don’t have to fully disassemble the rifle they see it cleaned ars for a while know that when you take the upper receiver off it’s usually flopping around it always takes one hand to stabilize the upper while you’re using the other hand to try to run the rod and manage patches and all that and it just it can be kind of troublesome i you make. Do but you shouldn’t have to well on the. Tipton’s best gun vise they include this nifty little l-shaped bracket here and. What i like to do with it is set it with the short side up slide it back underneath the trigger guard and then lock it down and it will hold the ar in. Shotgun fashion so that you can put your. Bore guide in here run your cleaning rod etc and be hands-free if you want to put. It back down to work on optics or something it’s really easy to slide out of the way lock back down push your pin through and you’re done also you can see. On this there is a long leg you can flip. This the other direction so the long leg. Is up if you’re working on something like side by side or over-under shotguns. And you want to be able to set it up that way you can do so this vise offers. You a ton of options it’s got some nice. Recesses down here on the base to give you a place to put solving bottles patches attachments whatever the. Only thing that i really wish it would have is i wish it had some kind of notch. Or cradle on the side so i can drop my cleaning rod into that and not worry. About it rolling off the workbench but other than that it works very well as i. Said it clamps a rifle in very securely there’s really no worry about your rifle falling out of this this ar is clamped. In here so tight i would take an earthquake to knock it out it really is fairly well secured now to the drawbacks. First of all the cost on this runs right. About $90 you can catch them on sale at midway every now and again and for. Ninety dollars you’re getting a very nice design but they use some fairly lightweight materials this is all molded. Plastic pretty much the entire thing with the exception of the places where your rifle. Actually contacts it is plastic that it. Has rubber pads where your rifle is going to contact the cradle and then the. Thumb screws are the knobs here all have. Metal studs on the other side that they. Screw into and they have metal inserts in the actual knobs themselves so you. Don’t have to worry about breaking the knobs unless you really do something stupid but the plastic is fairly. Flexible you can squeeze on it and feel. It move when you tighten the knobs down sometimes you’re worried about cracking. The plastic it hasn’t actually been an issue but it’s always a fear in the back your mind also when you go to cam the. Levers down while they work and they. Hold the rifle very well you can see the. Whole assembly up here flex when you cam those levers down and it really it’s a. Little bit more flex than i’d like to see overall the tipton’s best gun vise. Does exactly what it was designed to do and it does it very well i’d like to see. A little bit higher quality materials but my fear is that would raise the price considerably and at ninety dollars. Were already on the upper end of what i. Think is probably an acceptable price range for this kind of product. Here however it makes your cleaning jobs a whole lot easier it makes maintaining your weapon a whole lot easier since you no longer have to worry about it rolling around on the bench or getting knocked off and really if you’re doing weapons. Maintenance on a regular basis this is a great tool to have additionally for us. It allows us to lock a weapon in so that you can see it and i still have my hands-free to do various different tasks and show you different things on a weapon system so for us it works very. Well if you’ve got any questions or comments on the tipton’s vesica inviting. In the comment section below or send them to us on facebook or twitter if you’ve liked this video please give us that thumbs up if you want to get one of. These of your own we’ll leave you a link in the description below on where you. Can go to pick one up for yourself and. If your subscriber thank you very much. If you’re not please subscribe and finally get out and shoot.

Is an indispensable accessory for the. Serious shooter first you can cite in. Three to five shots will show you how to do that shortly second it doubles as a cleaning vice the. Way it works is that you can move the. Various sections support along these. Sliding bars here so that you can adjust. To any length gun even if you tighten it up you can even use it for some pistols. In order to sign in you need to be able. To fire a good three or five shot group. Our recommendation is to rearrange the. Components this way so if you have a stable base to fire your group from. First thing to do is fire a three or a. Five shot group because you really need two tight grouping to reference from. This is a three shot group that we fired. Using a or fifteen two to three you. Now that we made a cross type target for the simple reason that using this. Type of target is much easier to reference the alignment of the crosshairs it’s important to mark the. Center of the group, and we supply iridescent markers you put right over so the center of the group is right in the middle of it now but the purpose is. Exercise we have removed the target but in actuality you would leave the target in place the next thing you want to do is put the rest in the same approximate. Position that when you fire your shots and then you want to just the rest adjust the various sections so that the gun is firmly cradled in the rest make. Sure that the pedestal comes all the way up here so that the porn is resting solidly on it make sure the porn is tightness oddly in the v-notch this one shows that the rest is a good position tightening screws on the. Vice okay now that the stock of the gun. Is snugly anchored in the vice don’t make it too tight just so it doesn’t move about now you want to bear on the velcro strap around the front pull it. Down good and tight pull it back upon itself like this now the gun is solidly. Anchored at this point we need to. Reference our original point of aim now to do that unload your gun get a sit in. The vice just the way we have it here and then you don’t want to touch the adjustments on the scope at this point what we’re going to do is we’re going to move device left and right the wind age I’m going to use the elevation adjustments at the four corners of the vice to settle elevation to move the reticle the crosshair of the scope to exactly the point where we fired original shots now in our case that’s the center of the cross using bullseye target of course that’s the center of the bullseye this is the final step in. This step we’re going to align the point. Of impact and the point of aim in other words we’re going to get you sighted in you take the scope caps off get behind. Your gun and do not touch the vice. Must remain right where it is with the center of the reticle on your original point of aim which of course in our case was the center of the cross target and if you’re using the bullseye targets the center of the bullseye look for your. Sight and by turning your adjustment knobs walk the reticle on to the center of the point of impact which is the group that we fired and. Walk with the orange dot at that point. You are sighted in. You. You.

Welcome back to our channel I’m lauren with lock hart tactical and today we’ll be looking at the wheeler engineering master roll pin punch set well they’ve. Done it if combines the roll pin starter. Set and the ball profile roll pin punch set with the precision machined. Gunsmithing hammer all into one comprehensive kit both of the sets have. Knurled handles are machined and. Hardened from steel to prevent bending or breaking and start at 1/16 of an inch. And have nine roll pins ending in a 5/16. The ball profile roll pin punch set is. Designed with a ball profile tip to. Provide proper alignment of the roll pin and prevent damage to the firearm or the roll pin the ball tip profile is perfect. For driving set roll pins and recessing. Then into assemblies the ball profile helps prevent the punch from slipping off the roll pin and damaging the finish of your gun the roll pin starter set is. Designed with a counter bored tip to properly align and start the roll pin preventing damage to the firearm by slipping the roll pin into the recessed tip you can gain much-needed purchase for starting the roll pin into the hole this also helps provide alignment on roll pins for hard-to-reach spots the. Small hammer included in the package only weighs six ounces it has one side. Of the head made of nylon for precise. Work and non marring surfaces and one side of the head made of brass for harder strikes that won’t deform punches for more information visit us at lock hart tactical comm thanks for. Watching don’t forget to like this video comment down below subscribe to our channel and share it with your friends this is them alarm with lock hart tactical over and out. Try saying that sometimes ask all profile roll pin punch set up a ball. Roll but roll pin punch step.

Hey folks i recently did a video i know. Stuff here croyle and i was discussing. Getting a screw out of this it’s a beretta made in 1942 and that screw is. All tore up and i had mentioned how i actually destroyed three screwdriver. Tips getting us out one was a cheap. Gunsmithing screwdriver the other one. Was actually a craftsman screwdriver and. Then the third one was some other tip i. Don’t remember what it was the screw was. Blemished it was ripped a little bit before i started getting it out but by the time i was by the time i got it out it’s in bad condition now so i mentioned. All the coil help ease it out but there. Is another aspect of that and something else that if you’re a gun guy especially. If you’re in a military surplus and a little bit of gunsmithing even modern guns i mean pretty much anything you got to have a good screwdriver set and i had el cheapo and it cost me this screw so i. Would recommend this this one here is. From wheeler engineering i’ve had several different screwdriver kits this. One here is by far my favorite this is. Like their granddaddy this one here is everything comes with. This little layout here location guide. Talks about it here this is the deluxe gunsmithing screwdriver set and it’s. Outstanding this comes with everything. That you could need it has a shorter. Screw driver if you need more control more torque a little bit longer one if. You need need the distance has a i’ve. Never used this it’s a quarter-inch for. I guess if you want to put her in a. Ratcheting set or something put that in there i have not used. Here again if you need a little bit of extra distance a little bit extra reach and i’m not going to go over all this. Stuff here it’s everything you can imagine you have every flathead every. Screw that has probably ever been made we have a few phillips starr hex and. Here’s where it gets really interesting we have right here a weaver slash ruger. Scoring clamp it we have a redfield. Windage screw bit loop old windage screw. Bit this one here is specifically for. Mauser stocks most we have there is a. Not sure where i stuck it here actually. Just dropped this box right before i was doing it and everything fell out and i put it together real quick and i did not put it in very good order here we go. Here’s this is a millett rear sight adjustment grip screw bushing driver. This one here there’s a screw driver inside and i guess the bushing i’m not. Sure exactly all that works keeps it centered or whatever. Ruger colt single-action base pin m1 m1. A rear sight bit couple pin punches. Smith & wesson rebound spring glock. Replacement front sight bit remington. 870 trigger plate pin all kinds of stuff. Oh rover anymore as i was saying this is by far the best screwdriver set that i have found it’s. Got everything and as such. The rifle that i was referring to early. Earlier if i only had the proper biz you. Can get the proper thickness you can get the proper width this one here would. Have fit perfect and i wouldn’t have had. The screw destroyed i want to destroyed. This screw i also like that this comes. In a nice durable case solid as i said. Earlier i dropped this thing and it did not break you can find this set right. Here on amazon for around 63 bucks i. Think it’s just under 63 which is. Definitely worth it that screw that i. Just destroyed on that rifle is probably. Going to cost me i mean by the time you find somebody to carries that screw shipping and all that i mean you’re talking 20 30 bucks for that damaged screw to replace it so this is. Definitely worth it and it’s got. Everything you need it’s the deluxe gunsmithing screwdriver set from wheeler. You have any questions let me know semper fi.

Davidge screws can destroy the value of your favorite firearms and make disassembly impossible we’ve developed a screwdriver set at wheeler engineering that’ll solve the problem of damaged screws forever let me tell you about it unlike a normal screwdriver out bits are. Hollow ground, so they precisely fit each screw and prevent damage and with over 80 bits included in each set you’re sure. To find the right bit for every application ask for the wheeler gunsmithing screwdriver set at a store near you.

Hello this is joe angelo with alignment products today I’m going to demonstrate the use of the lyman borg am i will show. Setup and usage and examples of things to look for in your barrel and chamber areas inside the box you will find a 20. Inch 90-degree wand usb power adapter. With multi-voltage face plates a three. And a half inch color monitor sd card and card reader lens cleaner and cotton. Swabs for cleaning the camera and an instruction manual. once you have the board cam setup powered on and wait for the image to. Appear on the screen as you can see the. Want is marked where the lens is orientated and there are hash marks along the wand in one inch increments this will aid you if you happen to see something but want to know what inch marked so you can find it again and take a picture for review there is also a. Rubber stop on the one to help protect the muzzle crowd the brightness of the. Light is also adjustable on using the arrow keys once the board cam is powered. On you can start to insert the wand into. The muzzle of the firearm always making sure the firearm is unloaded and safe as. You start the wand down the barrel you see the lands and grooves of the rifling. You may see some glare from the light you can either adjust the light intensity or move the wand closer to the wall of the barrel the bore cam will. Show red copper following rough or. Machining marks pitting rusting fire. Cracking and general wear in the barrel and throat chamber area once you have. Located something in the barrel chamber throw the lining board cam will take a picture and save it to the sd card provided so that you can review them on the monitor or a computer at a later. Time in order to take a picture get the. Wide position so that it gets the best possible view of the area in question and press the capture button on the monitor you may also want to jot down. The inch designation and lens orientation so you can find that area again if need be to review pictures on. The monitor you will need to press and hold the mode button 3 seconds to enter. The review mode you can press the arrow buttons to scroll through the pictures taken To exit the review mode press and hold. The mode button for three seconds to. View pictures on your computer remove the sd card from the monitor and insert the card into the supplied reader then. Insert into an empty usb port on your computer the lyman board cam will store. The 3,600 pictures on the sd card provided a bottle of limbs cleaner and. Cotton swabs are provided these can be used to clean a mirror at the end of the wand dampen a cotton swab with the. Supplied lens cleaner and clean the mirror at the end of the wand clean any dirt lid etc off the lens that can be. Seen on the displayed image for more. Information on this product for any other products in the lyman family please visit lyman products comm.